Estate Parts

Thermal fuse. If the dryer overheats, this device stops the flow of electricity to the heat source and/or the entire dryer. It is located on the blower housing and cannot be reset. The most common cause for overheating is a vent tube clogged with lint, a birds nest or other debris.

Manufacturer Number 3392519

Watch our “Part Testing” video to determine if the thermal fuse has blown out and needs to be replaced.

Drive motor coupler. New style with metal sleeves for added strength. This version replaces all previous motor coupler styles and versions. For direct drive washing machines.

Manufacturer Number 285753A

Common symptom of failed coupler is washer will fill, not agitate or spin but will drain the water from the tub.

Dryer belt. This is the most common belt used on Whirlpool, Kenmore, Kitchenaid, Roper, Estate and other dryer brands. The belt is flat, 92-1/4 inches long, 1/4 inch wide and has 4 ribs and 3 grooves. It replaces many other belts, including some with 5 ribs and 4 grooves.

Manufacturer Number 341241

See our dryer belt diagram to see how this belt should be installed around the motor and idler pulleys.

Gas burner valve solenoids. Kit contains both the two wire and three wire solenoids. One solenoid is the primary and one is the safety. Both have to operate for the gas valve to open. Usually, one of them burns out but you should always replace them as a set.

Manufacturer Number 279834

These often fail intermittently, making diagnosis difficult. To test, watch the burner assembly while the dryer is heating. If the igniter glows for a while and then shuts off without the gas turning on, it usually means one of these coils is bad.

Dryer heating element. If your dryer does not heat, enter your model number into our Repair Help Section as this part is not the most common cause.

Manufacturer Number 279838

Normally, if you remove the old element a defective part will have a physical break in it. It can also be tested using a multimeter.See our Repair Help section for additional information

Washing machine agitator repair kit with a medium length cam (there are other kits available for different models). This kit should be used when the top part of the agitator is not moving properly but the bottom part is.

Manufacturer Number 285811

Drain pump for belt-less direct-drive washer, one large port, one small port.

Manufacturer Number 3363394

Mounts directly to the motor with two clips. A leaking pump may cause a small puddle in the front of the washer.

Washing machine agitator directional cogs, also known as "dog ears", 4 per package

Manufacturer Number 80040

Chrome drip bowl for 6" burner, electric range

Manufacturer Number W10196406RW

Lid switch assembly, Washing Machine.

Manufacturer Number 3949247

If the washer fills and agitates, but does not drain or spin then the lid switch has likely failed. Watch our “Part Testing” video to determine if the switch has failed and needs to be replaced.

Spanner nut wrench for MOST Whirlpool/Kenmore, General Electric & Maytag inner tub lock nuts

Manufacturer Number TB123A

Igniter kit, will replace round or flat style, with bracket, wire nuts and mounting screw. Caution! The black heating element portion of this part is EXTREMELY fragile. Use caution when handling.

Manufacturer Number 279311

Watch our “Part Testing” video to determine if the dryer igniter has burned out and needs to be replaced.

Chrome drip bowl for 8" burner, electric range

Manufacturer Number W10196405

Washing Machine agitator repair kit. *Short cam.

Manufacturer Number 285809

The teeth on the dog ears often wear out and cause the top of the agitator to not work properly.

Washing machine water inlet valve kit, with bracket

Manufacturer Number 285805

A long or slow fill cycle is often due to a restricted water valve. The valve should never be disassembled and cleaned, only replaced.

Door switch assembly

Manufacturer Number 3406107

Dryer cycling thermostat with internal bias heater, L155-25

Manufacturer Number 3387134

Glass carousel turntable tray. 13 inches in diameter

Manufacturer Number 1B71961A

Washing machine clutch assembly with hardware. *Blue spring for large capacity washers, black for compacts.

Manufacturer Number 285785

A worn clutch often causes a slower spin speed which leaves the clothes soaked after the cycle.

Heating element thermal cut-off (thermal fuse) 309 degrees and high-limit thermostat 250 degrees, with wiring kit.

Manufacturer Number 279816

Watch our “Part Testing” video to determine if the thermal fuse has blown out and needs to be replaced.

Ice and water filter in front access grille for refrigerators made by Whirlpool, including some Kitchen Aid and Kenmore refrigerators. This is manufacturer part 4396508, and it replaces 4392857, WF-NL300, WF-L500 and 4396163. Replace every 6 to 12 months.

Manufacturer Number 4396508

Suspension spring

Manufacturer Number 63907

A bad or broken suspension spring causes tub balancing problems during the spin cycle.

Replacement 8 cube icemaker kit, replaces many Whirlpool-made ice makers. Does not include shut off arm.

Manufacturer Number 4317943

You remove the shut off arm from the old icemaker lift it to the up position, unhook it from the fill cup bearing, and pull it out of the module.

Heating element thermal cut-off (thermal fuse) 360 degrees and high-limit thermostat 250 degrees.

Manufacturer Number 279769

Watch our “Part Testing” video to determine if the thermal fuse has blown out and needs to be replaced.

Heating element, 240 volts

Manufacturer Number 4391960

Watch our “Part Testing” video to determine if the dryer heating element has burned out and needs to be replaced.

Wheel assembly, upper dishrack

Manufacturer Number 8268655

Crisper pan

Manufacturer Number 2188656

Door bin

Manufacturer Number 2187172

40 watt frosted light bulb

Manufacturer Number 8009

Bracket, upper mounting

Manufacturer Number 8269145

Charcoal filter

Manufacturer Number 8206230A

Belt tension pulley

Manufacturer Number 691366

Plastic leveling leg

Manufacturer Number 49621

Rear drum support roller kit (2) in kit, Whirlpool-Kenmore, and others

Manufacturer Number 349241T

Repair kit for Whirlpool, Kenmore, Roper dryer; rollers, belt and idler pulley, for 29" wide Dryers built 1965 and later

Manufacturer Number 4392065

Universal door catch kit

Manufacturer Number 279570

Gasket kit, includes the strike latch

Manufacturer Number W10542314

40 Watt light bulb with small screw in base

Manufacturer Number 8206232A

Grease filter

Manufacturer Number W10208631A

Icemaker control module and motor assembly

Manufacturer Number W10190935

Motor, dryer drum drive with pulley for belt

Manufacturer Number 279827

Icemaker and water dispenser water inlet valve kit

Manufacturer Number 4318046

Universal receptacle kit, electric stove surface burners

Manufacturer Number 330031

Gas dryer sensor for igniter and flame

Manufacturer Number 338906

This flame sensor should be closed for continuity at room temperature. Check for continuity with a multi-meter before replacing.

Grease filter

Manufacturer Number 6802A

Bake element, 240 volts

Manufacturer Number 308180

Watch our “Part Testing” video to determine if the bake or broil element has burned out and needs to be replaced.

Fuse kit with wire harness and instructions *Always use new wiring harness.

Manufacturer Number 8193762

Watch our “Part Testing” video to determine if the thermal fuse has overheated and needs to be replaced. The fuse blowing is an indication of a problem in the heating element circuit like a shorted to ground element. Element can be tested, see video.

LP conversion kit

Manufacturer Number 49572A

High-limit thermostat, L250-80, with terminal extension arm

Manufacturer Number 3977767

This thermostat should be closed for continuity at room temperature, opens at around 250 degrees Fahrenheit. Check for continuity with a multi-meter before replacing.