Montgomery Wards Dryer Parts

Dryer belt. This is the most common belt used on Whirlpool, Kenmore, Kitchenaid, Roper, Estate and other dryer brands. The belt is flat, 92-1/4 inches long, 1/4 inch wide and has 4 ribs and 3 grooves. It replaces many other belts, including some with 5 ribs and 4 grooves.

Manufacturer Number 341241

See our dryer belt diagram to see how this belt should be installed around the motor and idler pulleys.

Gas burner valve solenoids. Kit contains both the two wire and three wire solenoids. One solenoid is the primary and one is the safety. Both have to operate for the gas valve to open. Usually, one of them burns out but you should always replace them as a set.

Manufacturer Number 279834

These often fail intermittently, making diagnosis difficult. To test, watch the burner assembly while the dryer is heating. If the igniter glows for a while and then shuts off without the gas turning on, it usually means one of these coils is bad.

Rear dryer drum bearing kit

Manufacturer Number 5303281153

Dryer drum belt, length 87.75", width 1/4"

Manufacturer Number 134503600

Heating element and rear housing assembly

Manufacturer Number 131553900

Watch our “Part Testing” video to determine if the dryer heating element has burned out and needs to be replaced.

Dryer door catch kit

Manufacturer Number 5366021400

Thermal fuse, high-limit thermostat kit for gas/electric dryer

Manufacturer Number LA-1053

Watch our “Part Testing” video to determine if the thermal fuse has overheated and needs to be replaced.

Gas dryer sensor for igniter and flame

Manufacturer Number 338906

This flame sensor should be closed for continuity at room temperature. Check for continuity with a multi-meter before replacing.

Blower wheel retaining ring

Manufacturer Number 25-7855

Front upper felt glide pad with nylon glides, adhesive and instructions

Manufacturer Number 5303937139

Gas valve solenoid coil kit, both 2 and 3 wire coil in kit

Manufacturer Number 5303931775

Thermal limiter (thermal fuse)

Manufacturer Number 134120900

Watch our “Part Testing” video to determine if the thermal fuse has overheated and needs to be replaced.

Lint filter

Manufacturer Number 53-0918

Door catch kit, includes catch and clip (metal)

Manufacturer Number LA-1003

Rear bearing support cup

Manufacturer Number 131825900

Lint filter screen and mounting frame

Manufacturer Number 131390300

Heating element wire coil

Manufacturer Number 5300622032

Watch our “Part Testing” video to determine if the dryer heating element has burned out and needs to be replaced.

Drum support roller kit with axles and mounting screws. Kit has been updated it has 1 plastic spacer that is the thickness of 2 spacers.

Manufacturer Number LA-1008

Dryer belt length 87 3/4”, width 1/2”, characteristics, flat

Manufacturer Number 5303281154

Heating element assembly with replacement high limit thermostat, L248-80 (240 Volt-4750 Watt)

Manufacturer Number LA-1044

Watch our “Part Testing” video to determine if the dryer heating element has burned out and needs to be replaced.

Blower wheel clamp

Manufacturer Number 312967

Front glide kit, (1) right (1) left glide (2) pads with adhesive backing and (1) cylinder support brace. Instructions included.

Manufacturer Number 12002126

Igniter, gas dryer

Manufacturer Number 5303937186

Watch our “Part Testing” video to determine if the dryer igniter has burned out and needs to be replaced.

Terminal block kit for electric range and dryer cords

Manufacturer Number 5304409888

High temperature adhesive for installing rubber and felt seals

Manufacturer Number 5308027429

Idler tension pulley with bracket

Manufacturer Number 5303212849

Blower wheel, 3-1/8” deep, 8” fin diameter, 7-1/8” hub diameter, 20 standard fins, ½” diameter motor shaft, 3/8” motor shaft diameter to flat side of shaft. Spring clamp not included.

Manufacturer Number 31001317

Leveling leg

Manufacturer Number 131527400

Blower wheel, 3-1/8” deep, 8” fin diameter, 7-1/8” hub diameter, 20 standard fins, ½” diameter motor shaft, 7/16” motor shaft diameter to flat side of shaft. Spring clamp not included. Series B10 only

Manufacturer Number 31001043

Blower wheel, 3-1/8” deep, 7-1/2” fin diameter, 6-3/4” hub diameter, 20 standard fins, ½” diameter motor shaft, 7/16” motor shaft diameter to flat side of shaft. Most common.

Manufacturer Number 53-0106

90 Degree Close Dryer Vent Elbow -Uniquely designed elbow to allow close placement of dryer to the wall. Energy efficient metal construction for safe operation. Simple instructions for easy installation with common household tools.

Manufacturer Number 5305514872

Clip, guide

Manufacturer Number 5303281074

Dryer door seal. *Seal may come as one piece, hold at one end and pull apart to separate.

Manufacturer Number 31001529

Seal may come as one piece, hold at one end and pull apart to separate.

8 Foot Flexible Dryer Venting Kit

Manufacturer Number 5305512431

Paint, touch-up, white

Manufacturer Number 5303321319

Glow bar igniter with wire harness

Manufacturer Number 31001556

Watch our “Part Testing” video to determine if the dryer igniter has burned out and needs to be replaced.

Seal, blower housing

Manufacturer Number 134417000

Flame sensor for gas dryer

Manufacturer Number 5303281135

Top screw

Manufacturer Number 3196164

Screw, 10-24 3/8

Manufacturer Number 90767

Drive motor assembly

Manufacturer Number W10410996

Screw

Manufacturer Number 489483

Strike, dryer door

Manufacturer Number 5303207102

Selector knob, white

Manufacturer Number 21001239

Control thermostat, L146-25F, 240 Volt internal heater

Manufacturer Number 31001192

Screw

Manufacturer Number 489478

Clip, cabinet top

Manufacturer Number 25-7220

Dryer Vent Pipe - Deflecto 4-inch by 24-inch aluminum dryer vent pipe.

Manufacturer Number DP244

Door switch

Manufacturer Number 53-0148