Enter Part or Model Number for best results

(Where is my model number?)

GE Dryer Won't Start

DHDSR48EF2WW

The 5 most common part(s) or condition(s) which contribute to the symptom Dryer won't start are listed below. Check or test each item and watch any available videos. If you are still unable to solve the problem you may need to do additional research and troubleshooting. Remember, with our 365 Days. Period.® return policy you can return any part for any reason. So, go ahead and buy it to try it. No other parts retailer offers this unconditional return policy.

For the symptom you selected, these are the most common parts or causes, ordered by the likelihood of fixing the symptom.

Grid is 1 inch square
Door Switch - Part # 1472475 Mfg Part # WE4M415

Door Switch

RepairClinic Item # 1472475

The door switch is located near the dryer door and is activated when the door is closed. If the door switch fails, the dryer won't start at all. Most door switches will make an audible click when they are activated. If the door switch makes a clicking sound when activated it is probably not defective. If it doesn't make a click, it can be checked with an ohm meter or continuity checker. The door switch is relatively easy to replace and is usually not very expensive.

Order now and this item will ship out tomorrow - or it's FREE!

$14.15

Grid is 1 inch square
Drive Motor - Part # 1256970 Mfg Part # WE17X10010

Drive Motor

RepairClinic Item # 1256970

On most dryers the drive motor turns the drum and the blower wheel to exhaust the air. If the dryer won't start the motor might be defective. Before replacing the motor, check the thermal fuse, start switch and door switch because all three are more likely the cause. If the dryer won't start and the dryer motor makes a humming noise there might be something caught in the blower wheel, or the drum might be binding. Try removing the belt from the motor and checking the blower wheel for obstructions. The dryer motor can't be tested easily. If the more common components have been checked and it seems the motor itself is defective, it will need to be replaced. It is not serviceable.

Order now and this item will ship out tomorrow - or it's FREE!

$148.60

Grid is 1 inch square
Drive Belt - Part # 1381519 Mfg Part # WE12M29

Drive Belt

RepairClinic Item # 1381519

On most dryers, if the drive belt breaks the motor can still be heard and it will still be blowing air out the exhaust tube, but the drum will not spin. However, in some dryers when the drive belt breaks the tension pulley arm trips a switch which shuts off power to the entire dryer. If the dryer won't start, check to see if the belt is broken. If it is, replace the belt and the dryer should be fine. If the belt is not broken, check the other components that can fail when the dryer won't start.

Order now and this item will ship out tomorrow - or it's FREE!

$19.20

Other Causes and Conditions

Incoming Power Problem

If the dryer won't start, check to make certain there is electricity to the dryer. For a gas dryer, unplug the dryer from the wall and plug something else into the outlet to see if it's working. For an electric dryer, check the home circuit breaker or fuses. If they are working, check the outlet where the dryer plugs in with a volt meter. There should be between 208 and 240 volts. If there is power to the dryer, check the more common items in this troubleshooting guide.

Grid is 1 inch square
Timer - Part # 276471 Mfg Part # WE4M189

Timer

RepairClinic Item # 276471

The timer is normally not at fault when the dryer won't start. In many situations where timers are replaced they end up being returned. First, check all of the more common components in this troubleshooting guide before replacing the timer. If the dryer won't start, the cause is much more likely to be a thermal fuse or switch. The timer can not be tested, it must be replaced if it is defective.

Order now and this item will ship out tomorrow - or it's FREE!

$90.45

Back to Symptom List