Enter Part or Model Number for best results

(Where is my model number?)

Kenmore Refrigerator Ice Maker Not Working

106.56532400

The 7 most common part(s) or condition(s) which contribute to the symptom Refrigerator ice maker not working are listed below. Check or test each item and watch any available videos. If you are still unable to solve the problem you may need to do additional research and troubleshooting. Remember, with our 365 Days. Period.® return policy you can return any part for any reason. So, go ahead and buy it to try it. No other parts retailer offers this unconditional return policy.

For the symptom you selected, these are the most common parts or causes, ordered by the likelihood of fixing the symptom.

Other Causes and Conditions

Freezer Temperature is Above 10 Degrees F (-12C)

If the ice maker is not working check the temperature of the freezer. If the freezer temperature is above 10 degrees F. (-12C) the ice maker will not work properly. It functions best when the freezer temperature is set between 0 and five degrees F. (-18 to -15C). If the freezer temp is too high make sure the condenser coil is clean and the condenser fan is working to cool the condenser and compressor. Check the evaporator coil for frost. If too much frost is built up the air can't circulate thru the coil and you will need to check the defrost components for a failure.

Grid is 1 inch square
Water Inlet Valve - Part # 1938614 Mfg Part # W10408179

Water Inlet Valve

RepairClinic Item # 1938614

If the refrigerator ice maker is not working the water inlet valve might be defective. The water inlet valve is an electro-mechanical valve. The coil can show good for continuity and still not let the water thru.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

Other Causes and Conditions

Low Water Pressure from House Supply

If the ice maker is not working the water pressure in the house might be too low. The water inlet valve which supplies water to the ice maker is designed to work with a minimum of 20 psi of water pressure.

Grid is 1 inch square
Door Switch - Part # 438889 Mfg Part # 2149705

Door Switch

RepairClinic Item # 438889

If the refrigerator ice maker is not working, the door switch might be defective. When the freezer door is opened the freezer door switch does two things, it turns on the light in the freezer and turns off the ice maker and dispenser. If the door switch fails the dispenser will not turn on. The switch can be checked for continuity with an Ohm meter. If it doesn’t have continuity it should be replaced.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

Grid is 1 inch square
Ice Level Control Board - Part # 921526 Mfg Part # 4389102

Ice Level Control Board

RepairClinic Item # 921526

If the ice maker is not working the ice level control board might be defective. This refrigerator is equipped with an infrared light beam to detect the level of ice in the ice bucket. As the level of ice reaches the top, the beam is interrupted and the ice maker shuts off. As ice is used up and the level of ice drops below the beam, the ice maker starts up again. If the ice level control board fails, the ice maker will stop making ice.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

Grid is 1 inch square
Water Filter - Part # 1053692 Mfg Part # 4396710

Water Filter

RepairClinic Item # 1053692

If the refrigerator ice maker is not working the water filter might be clogged. Try changing the water filter.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

Grid is 1 inch square
Icemaker Mold Thermostat - Part # 2942 Mfg Part # 627985

Icemaker Mold Thermostat

RepairClinic Item # 2942

If the ice maker is not working the icemaker mold thermostat might be defective. Inside the control module of the ice maker is a thermostat which monitors the temperature of the ice mold (ice tray). Once the mold reaches the proper temperature the ice maker starts a harvest cycle by ejecting the ice cubes and refilling with water. If the mold thermostat is defective the ice maker doesn't advance. The thermostat can be checked for continuity. Replace it as needed.The freezer temp should be between 0-5 degrees for optimum performance.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

Back to Symptom List