Enter Part or Model Number for best results

(Where is my model number?)

Kenmore Washer Won't Spin

110.23032101

The 10 most common part(s) or condition(s) which contribute to the symptom Washer won't spin are listed below. Check or test each item and watch any available videos. If you are still unable to solve the problem you may need to do additional research and troubleshooting. Remember, with our 365 Days. Period.® return policy you can return any part for any reason. So, go ahead and buy it to try it. No other parts retailer offers this unconditional return policy.

For the symptom you selected, these are the most common parts or causes, ordered by the likelihood of fixing the symptom.

Grid is 1 inch square
Lid Switch Assembly - Part # 722578 Mfg Part # 8054980

Lid Switch Assembly

RepairClinic Item # 722578

If the washer won't spin the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$26.15

Grid is 1 inch square
Motor Coupling - Part # 1195967 Mfg Part # 285753A

Motor Coupling

RepairClinic Item # 1195967

If the washer won't spin the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and transmission. Another common problem is the lid switch.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$11.40

Grid is 1 inch square
Drive Block - Part # 2858 Mfg Part # 389140

Drive Block

RepairClinic Item # 2858

If the washer won't spin the drive block might be worn out or may have come loose. Underneath the agitator the drive block connects the inner tub (the one that spins around) to the transmission. If the drive block wears out the transmission shaft will still spin but the tub may not - or it may spin slowly. This also usually causes a lot of noise. The drive block is relatively easy to replace.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$15.30

Grid is 1 inch square
Clutch - Part # 831493 Mfg Part # 8299642

Clutch

RepairClinic Item # 831493

If the washer won't spin, the clutch assembly might be worn out. The clutch assembly makes the connection between the transmission and the inner tub. It is designed to allow the tub to get up to the proper spin speed gradually. As the clutch wears out it may prevent the tub from spinning. The clutch is not repairable, if it is loud or not working properly it will need to be replaced.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$35.15

Grid is 1 inch square
Clutch Band kit - Part # 547692 Mfg Part # 3951993

Clutch Band kit

RepairClinic Item # 547692

If the washer won't spin, the clutch band kit might be worn out. The clutch makes the connection between the transmission and the inner tub. It is designed to allow the tub to get up to the proper spin speed gradually. As the clutch wears out it may prevent the tub from spinning. If the washer won't spin, this clutch band kit may need to be replaced.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$18.65

Grid is 1 inch square
Drive Motor - Part # 831562 Mfg Part # 8314869

Drive Motor

RepairClinic Item # 831562

If the washer won't spin the drive motor might be defective. This is not common. Check all of the other related parts to this symptom before replacing the motor. If the motor is visibly burned out or physically damaged It will have to be replaced.

Oversize Part – Special Shipping Required

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$223.35

Grid is 1 inch square
Bearing - Part # 470615 Mfg Part # 285203

Bearing

RepairClinic Item # 470615

If the washer won't spin the tub bearing might need to be replace. This is a very involved repair and will require disassembling most of the washer. The manufacturer recommends that if possible the complete outer tub and bearing be replaced rather than attempting to replace just the bearing in the tub. If the bearing is bad the problem is going to get worse very quickly and so either the drum and bearing will need to be replaced or the washing machine.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$26.05

Grid is 1 inch square
Bearing - Part # 1180074 Mfg Part # 8546455

Bearing

RepairClinic Item # 1180074

If the washer won't spin the tub bearing might need to be replace. This is a very involved repair and will require disassembling most of the washer. The manufacturer recommends that if possible the complete outer tub and bearing be replaced rather than attempting to replace just the bearing in the tub. If the bearing is bad the problem is going to get worse very quickly and so either the drum and bearing will need to be replaced or the washing machine.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$21.75

Grid is 1 inch square
Basket Drive - Part # 1254 Mfg Part # 285792

Basket Drive

RepairClinic Item # 1254

If the washer won't spin the basket drive clutch might be worn out. The basket drive sits on top of the transmission and engages with the inner tub. If the basket drive wears out the tub won't spin.

Place your order by 8:00 PM ET and this item will ship out today - or it's FREE!

$129.40

Grid is 1 inch square
Transmission - Part # 423 Mfg Part # 3360629

Transmission

RepairClinic Item # 423

If the washer won't spin the transmission might be worn out or defective. There are numerous more likely causes when a washer won't spin, which should be checked first.

Special Shipping Required

Order now and this item will ship out today - or it's FREE!

$186.35

Back to Symptom List