Washer/Dryer Combo Parts

Dryer drum slide. There are two of these needed on your dryer. These go on the outer most slots on the front bearing. Sold individually will need to purchase two*

Manufacturer Number WE1M504

The drum slides support the front of the dryer drum instead of rollers or bearings. As they wear out the dryer will make more noise.

Dryer drum slide. There are two of these needed on your dryer. These go on the inner most slots on the front bearing. Sold individually will need to purchase two*

Manufacturer Number WE1M1067

The drum slides support the front of the dryer drum instead of rollers or bearings. As they wear out the dryer will make more noise.

Thermal fuse. If the dryer overheats, this device stops the flow of electricity to the heat source and/or the entire dryer. It is located on the blower housing and cannot be reset. The most common cause for overheating is a vent tube clogged with lint, a birds nest or other debris.

Manufacturer Number 3392519

Watch our “Part Testing” video to determine if the thermal fuse has blown out and needs to be replaced.

Drive motor coupler. New style with metal sleeves for added strength. This version replaces all previous motor coupler styles and versions. For direct drive washing machines.

Manufacturer Number 285753A

Common symptom of failed coupler is washer will fill, not agitate or spin but will drain the water from the tub.

Dryer belt. This is the most common belt used on Whirlpool, Kenmore, Kitchenaid, Roper, Estate and other dryer brands. The belt is flat, 92-1/4 inches long, 1/4 inch wide and has 4 ribs and 3 grooves. It replaces many other belts, including some with 5 ribs and 4 grooves.

Manufacturer Number 341241

See our dryer belt diagram to see how this belt should be installed around the motor and idler pulleys.

Gas burner valve solenoids. Kit contains both the two wire and three wire solenoids. One solenoid is the primary and one is the safety. Both have to operate for the gas valve to open. Usually, one of them burns out but you should always replace them as a set.

Manufacturer Number 279834

These often fail intermittently, making diagnosis difficult. To test, watch the burner assembly while the dryer is heating. If the igniter glows for a while and then shuts off without the gas turning on, it usually means one of these coils is bad.

Dryer heating element. If your dryer does not heat, enter your model number into our Repair Help Section as this part is not the most common cause.

Manufacturer Number 279838

Normally, if you remove the old element a defective part will have a physical break in it. It can also be tested using a multimeter.See our Repair Help section for additional information

Front drum bearing. NOTE: The drum slides should also be replaced and are NOT included with this part, you must purchase two of each separately. Please see the "Related Items" for this part.

Manufacturer Number WE3M26

Washing machine agitator repair kit with a medium length cam (there are other kits available for different models). This kit should be used when the top part of the agitator is not moving properly but the bottom part is.

Manufacturer Number 285811

Drain pump for belt-less direct-drive washer, one large port, one small port.

Manufacturer Number 3363394

Mounts directly to the motor with two clips. A leaking pump may cause a small puddle in the front of the washer.

Drum support roller with bearing

Manufacturer Number 12001541

Both rollers should be replaced at the same time

Washing machine agitator directional cogs, also known as "dog ears", 4 per package

Manufacturer Number 80040

Rear dryer drum bearing kit

Manufacturer Number 5303281153

Drain pump and motor assembly

Manufacturer Number 4681EA2001T

Shipping bolt assembly. 6-1/4 inches long. Install before moving washing machine, remove before use.

Manufacturer Number 4011FR3159D

Lid switch assembly, Washing Machine.

Manufacturer Number 3949247

If the washer fills and agitates, but does not drain or spin then the lid switch has likely failed. Watch our “Part Testing” video to determine if the switch has failed and needs to be replaced.

Spanner nut wrench for MOST Whirlpool/Kenmore, General Electric & Maytag inner tub lock nuts

Manufacturer Number TB123A

Shipping bolt assembly. 4-3/4 inches long. Install before moving washing machine, remove before use.

Manufacturer Number 4011FR3159E

Dryer drum drive belt, 89-1/2 inches long, 4 ribs

Manufacturer Number WE12M29

Igniter kit, will replace round or flat style, with bracket, wire nuts and mounting screw. Caution! The black heating element portion of this part is EXTREMELY fragile. Use caution when handling.

Manufacturer Number 279311

Watch our “Part Testing” video to determine if the dryer igniter has burned out and needs to be replaced.

Door strike/catch, Front Load Washer

Manufacturer Number 131763310

Drum support roller

Manufacturer Number 37001042

Washing machine water inlet valve kit, with bracket

Manufacturer Number 285805

A long or slow fill cycle is often due to a restricted water valve. The valve should never be disassembled and cleaned, only replaced.

Dryer belt, length 93 3/8”, width 3/8”, characteristics, 5 ridges, flat

Manufacturer Number 40111201

Door switch assembly

Manufacturer Number 3406107

Door lock and switch assembly. A select few washers will require a new wire harness kit and door strike for this item to work per the manufacturer. If assembly does not wire directly in see Related Items for harness and strike.

Manufacturer Number 131763202

A select few washers will require a new wire harness kit and door strike for this item to work per the manufacturer. If assembly does not wire directly in see Related Items for harness and strike.

Dryer cycling thermostat with internal bias heater, L155-25

Manufacturer Number 3387134

Belt, dryer drum drive

Manufacturer Number Y312959

Washing machine clutch assembly with hardware. *Blue spring for large capacity washers, black for compacts.

Manufacturer Number 285785

A worn clutch often causes a slower spin speed which leaves the clothes soaked after the cycle.

Heating element thermal cut-off (thermal fuse) 309 degrees and high-limit thermostat 250 degrees, with wiring kit.

Manufacturer Number 279816

Watch our “Part Testing” video to determine if the thermal fuse has blown out and needs to be replaced.

Suspension spring

Manufacturer Number 63907

A bad or broken suspension spring causes tub balancing problems during the spin cycle.

Heating element thermal cut-off (thermal fuse) 360 degrees and high-limit thermostat 250 degrees.

Manufacturer Number 279769

Watch our “Part Testing” video to determine if the thermal fuse has blown out and needs to be replaced.

Heating element, 240 volts

Manufacturer Number 4391960

Watch our “Part Testing” video to determine if the dryer heating element has burned out and needs to be replaced.

Lid switch assembly

Manufacturer Number 3949238

Watch our “Part Testing” video to determine if the switch has failed and needs to be replaced.

Heating element assembly, 240 volts

Manufacturer Number 3387747

Watch our “Part Testing” video to determine if the dryer heating element has burned out and needs to be replaced.

Dryer drum belt, length 87.75", width 1/4"

Manufacturer Number 134503600

Dryer thermistor assembly

Manufacturer Number 8577274

The thermistor should read approximately 11.9K Ohms of resistance at 21 degrees Celsius (70 degrees Fahrenheit).

Drum glide pad (Replace in Pairs)

Manufacturer Number 37001298

Belt tension pulley

Manufacturer Number 691366

Plastic leveling leg

Manufacturer Number 49621

Rear drum support roller kit (2) in kit, Whirlpool-Kenmore, and others

Manufacturer Number 349241T

Front drum support glide, 2 required. *Note: Requires rivet tool-purchase locally.

Manufacturer Number 306508

Drain hose with bellows for flexibility during wash and spin cycle. Use cleanout to remove debris.

Manufacturer Number 4738ER1002A

Dryer belt, length 93 1/2”, width 1/4”, characteristics, 4 ridges, flat

Manufacturer Number 661570

Sensor assembly-HALL (motor) sensor

Manufacturer Number 6501KW2002A

Universal door catch kit

Manufacturer Number 279570

Drum roller axle

Manufacturer Number 6-3129480

Blower wheel for dryer exhaust, with clamp

Manufacturer Number Y303836

Lint filter

Manufacturer Number W10120998