Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Whirlpool Microwave Power Cord Replacement #W10269470

07:59
6.3k
14
This video provides step-by-step instructions for replacing the power cord on Whirlpool microwaves. The most common reasons for replacing the power cord are if it is worn or damaged or when you move with an older microwave with an power cord that does not fit the outlets in your new home.

All of the information in this power cord replacement video is applicable to the following brands: Whirlpool, Amana, Maytag, Estate, KitchenAid

Tools used: Phillips head screwdriver, insulated screwdriver

Step By Step Instructions

1
Because of the high voltage and high current used by microwave ovens, be aware that repairing this appliance poses a substantial risk for injury or death if precautions are not taken. You should always unplug the microwave before you attempt any disassembly.
2
Since high voltage capacitors used in microwaves may retain a charge even after the microwave has been unplugged, we recommend that only experienced professionals access and replace internal components. To replace the power cord on your microwave oven, you will need to uninstall the appliance. This will require two people.
3
Have an assistant support the microwave while you remove the mounting bolts from the upper cabinet.
4
Carefully tilt the microwave down and pull the power cord through the hole in the cabinet.
5
Now, lift the microwave off the rear mounting bracket and set it on a sturdy surface, resting on a towel or blanket.
6
Unthread the screws securing the grill.
7
Pull the grill forward from the top to remove.
8
If still in place, remove the glass turntable and support.
9
Now tip the microwave so it rests on its back panel and remove the bottom panel by using a phillips-head screwdriver to unthread the mounting screws.
10
With the screws removed, detach the panel and disconnect the wire harness.
11
Detach the grommet from the frame and pull the wire free.
12
Note the orientation of the turntable motor wires then slide off the insulators.
13
Depress the locking tabs to disconnect the wires and you can fully remove the bottom panel.
14
Return the microwave to its upright position and remove all of the screws securing the cabinet.
15
Unthread the screws securing the blower cover and remove the cover.
16
You can now fully remove the cabinet.
17
You should release the potentially stored electrical charge in the capacitor to avoid injury.
18
You can do this by placing a screwdriver with an insulated handle across each set of terminals.
19
Be very careful not to touch the screwdriver blade when doing this.
20
Note the orientation of the power cord wires then disconnect them from the noise filter board.
21
Remove the screw and washer to release the grounding wire.
22
You can now fully remove the old power cord.
23
Install the new power cord by first connecting the wires to the appropriate terminals on the noise filter board.
24
Secure the grounding wire to the frame with the screw and washer.
25
With the wires secured, position the new cord in the bracket.
26
Reposition the cabinet by aligning the top edge first.
27
Then push the sides forward making sure the tabs on the sides of the cabinet align with the frame.
28
Replace the screws to secure the cabinet.
29
Reposition the blower cover and secure it with the screws.
30
Rest the microwave on its back panel.
31
Replace the bottom panel by first reconnecting the turntable motor wires to the appropriate terminals.
32
Slide the insulators over the terminals.
33
Align the wire in the frame and secure it with the grommet then reconnect the wire harness.
34
Fully reposition the bottom panel and secure it with the screws.
35
Return the microwave to its upright position.
36
Realign the grill and snap it into place then rethread the screws to secure.
37
Now carefully reposition the microwave on the mounting bracket by hooking the back edge of the appliance on the bracket tabs.
38
Insert the power cord through the hole in the upper cabinet.
39
Lift the microwave up and secure the mounting bolts.
40
Plug the new power cord in.
41
Replace the turntable and support and your microwave oven should be ready for use.
Description
This video provides step-by-step instructions for replacing the power cord on Whirlpool microwaves. The most common reasons for replacing the power cord are if it is worn or damaged or when you move with an older microwave with an power cord that does not fit the outlets in your new home.

All of the information in this power cord replacement video is applicable to the following brands: Whirlpool, Amana, Maytag, Estate, KitchenAid

Tools used: Phillips head screwdriver, insulated screwdriver
Step-By-Step Instructions
1
Because of the high voltage and high current used by microwave ovens, be aware that repairing this appliance poses a substantial risk for injury or death if precautions are not taken. You should always unplug the microwave before you attempt any disassembly.
2
Since high voltage capacitors used in microwaves may retain a charge even after the microwave has been unplugged, we recommend that only experienced professionals access and replace internal components. To replace the power cord on your microwave oven, you will need to uninstall the appliance. This will require two people.
3
Have an assistant support the microwave while you remove the mounting bolts from the upper cabinet.
4
Carefully tilt the microwave down and pull the power cord through the hole in the cabinet.
5
Now, lift the microwave off the rear mounting bracket and set it on a sturdy surface, resting on a towel or blanket.
6
Unthread the screws securing the grill.
7
Pull the grill forward from the top to remove.
8
If still in place, remove the glass turntable and support.
9
Now tip the microwave so it rests on its back panel and remove the bottom panel by using a phillips-head screwdriver to unthread the mounting screws.
10
With the screws removed, detach the panel and disconnect the wire harness.
11
Detach the grommet from the frame and pull the wire free.
12
Note the orientation of the turntable motor wires then slide off the insulators.
13
Depress the locking tabs to disconnect the wires and you can fully remove the bottom panel.
14
Return the microwave to its upright position and remove all of the screws securing the cabinet.
15
Unthread the screws securing the blower cover and remove the cover.
16
You can now fully remove the cabinet.
17
You should release the potentially stored electrical charge in the capacitor to avoid injury.
18
You can do this by placing a screwdriver with an insulated handle across each set of terminals.
19
Be very careful not to touch the screwdriver blade when doing this.
20
Note the orientation of the power cord wires then disconnect them from the noise filter board.
21
Remove the screw and washer to release the grounding wire.
22
You can now fully remove the old power cord.
23
Install the new power cord by first connecting the wires to the appropriate terminals on the noise filter board.
24
Secure the grounding wire to the frame with the screw and washer.
25
With the wires secured, position the new cord in the bracket.
26
Reposition the cabinet by aligning the top edge first.
27
Then push the sides forward making sure the tabs on the sides of the cabinet align with the frame.
28
Replace the screws to secure the cabinet.
29
Reposition the blower cover and secure it with the screws.
30
Rest the microwave on its back panel.
31
Replace the bottom panel by first reconnecting the turntable motor wires to the appropriate terminals.
32
Slide the insulators over the terminals.
33
Align the wire in the frame and secure it with the grommet then reconnect the wire harness.
34
Fully reposition the bottom panel and secure it with the screws.
35
Return the microwave to its upright position.
36
Realign the grill and snap it into place then rethread the screws to secure.
37
Now carefully reposition the microwave on the mounting bracket by hooking the back edge of the appliance on the bracket tabs.
38
Insert the power cord through the hole in the upper cabinet.
39
Lift the microwave up and secure the mounting bolts.
40
Plug the new power cord in.
41
Replace the turntable and support and your microwave oven should be ready for use.

Applicable Product Model

Microwave
Brand
Product Type
Model
Subtype
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$8.99
Cleaner
Cleaner
$20.66
Cleaner
Cleaner
$14.18
Cleaner
Cleaner
$22.37
Total$0.00

Related Articles & Videos