Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

GE Microwave Power Cord Replacement #WB18X10491

loading...

07:30
16k
46
This video provides step-by-step instructions for replacing the power cord on GE microwaves. The most common reasons for replacing the power cord are if it is worn or damaged or when you move with an older microwave with a power cord that does not fit the outlets in your new home.

All of the information in this fan motor replacement video is applicable to the following brands: GE

Tools used: Phillips head screwdriver, T20 tamper-proof Torx bit screwdriver, insulated needle-nose pliers

Step By Step Instructions

1
Because of the high voltage and high current used by microwave ovens, be aware that repairing this appliance poses a substantial risk for injury or death if precautions are not taken. You should always unplug the microwave before you attempt any disassembly.
2
Since high voltage capacitors used in microwaves may retain a charge even after the microwave has been unplugged, we recommend that only experienced professionals access and replace internal components. To replace the power cord on your microwave oven, you will need to uninstall the appliance.
3
Have an assistant support the microwave while you remove the mounting bolts from the upper cabinet.
4
Carefully tilt the microwave down and pull the power cord through the hole in the cabinet.
5
Now, lift the microwave off the rear mounting bracket and set it on a sturdy surface, resting on a towel or blanket.
6
Use a phillips-head screwdriver to unthread the two mounting screws securing the grill.
7
With the screws unthreaded, open the oven door then slide the grill to the left and lift it up to remove.
8
If still in place, remove the glass turntable and support.
9
Now tip the microwave so it rests on its back panel and release the bottom panel by unthreading the mounting screws.
10
Disconnect the wire harness release the wires from the twist retainer and you can fully remove the bottom panel.
11
Return the microwave to its upright position and remove all of the screws securing the cabinet.
12
You will need to use a t-20 tamper-proof torx bit screwdriver to remove the bottom screws on the left and right sides.
13
Carefully remove the cabinet.
14
To avoid injury, you should release the potentially stored electrical charge in the capacitor.
15
You can do this by using needle-nose pliers with an insulated handle to touch both terminals simultaneously.
16
Be very careful not to touch the metal portion of the tool.
17
Now disconnect the power cord wire connecter.
18
Remove the screw securing the grounding wire.
19
With the grounding wire released, you can fully remove the old cord.
20
Install the new power cord by first connecting the wire connecter.
21
Secure the grounding wire to the base with the screw.
22
Position the power cord in the support bracket then reinstall the cabinet.
23
Make sure the tabs on the sides of the cabinet align with the frame.
24
Replace the screws to secure the cabinet.
25
Rest the microwave on its back panel.
26
Reinstall the bottom panel by first reconnecting the wire harness then secure the wires in the twist retainer.
27
Fully reposition the bottom panel and secure it with the screws.
28
Return the microwave to its upright position.
29
Make sure the charcoal filter is properly positioned then replace the grill by inserting the tabs into the slots in the frame.
30
Slide the grill to the right and rethread the mounting screws.
31
Now carefully reposition the microwave on the mounting bracket by hooking the back edge of the appliance on the bracket tabs.
32
Insert the power cord through the hole in the upper cabinet.
33
Lift the microwave up and secure the mounting bolts.
34
Plug the new power cord in.
35
Replace the turntable and support and your microwave oven should be ready for use.
Description
This video provides step-by-step instructions for replacing the power cord on GE microwaves. The most common reasons for replacing the power cord are if it is worn or damaged or when you move with an older microwave with a power cord that does not fit the outlets in your new home.

All of the information in this fan motor replacement video is applicable to the following brands: GE

Tools used: Phillips head screwdriver, T20 tamper-proof Torx bit screwdriver, insulated needle-nose pliers
Step-By-Step Instructions
1
Because of the high voltage and high current used by microwave ovens, be aware that repairing this appliance poses a substantial risk for injury or death if precautions are not taken. You should always unplug the microwave before you attempt any disassembly.
2
Since high voltage capacitors used in microwaves may retain a charge even after the microwave has been unplugged, we recommend that only experienced professionals access and replace internal components. To replace the power cord on your microwave oven, you will need to uninstall the appliance.
3
Have an assistant support the microwave while you remove the mounting bolts from the upper cabinet.
4
Carefully tilt the microwave down and pull the power cord through the hole in the cabinet.
5
Now, lift the microwave off the rear mounting bracket and set it on a sturdy surface, resting on a towel or blanket.
6
Use a phillips-head screwdriver to unthread the two mounting screws securing the grill.
7
With the screws unthreaded, open the oven door then slide the grill to the left and lift it up to remove.
8
If still in place, remove the glass turntable and support.
9
Now tip the microwave so it rests on its back panel and release the bottom panel by unthreading the mounting screws.
10
Disconnect the wire harness release the wires from the twist retainer and you can fully remove the bottom panel.
11
Return the microwave to its upright position and remove all of the screws securing the cabinet.
12
You will need to use a t-20 tamper-proof torx bit screwdriver to remove the bottom screws on the left and right sides.
13
Carefully remove the cabinet.
14
To avoid injury, you should release the potentially stored electrical charge in the capacitor.
15
You can do this by using needle-nose pliers with an insulated handle to touch both terminals simultaneously.
16
Be very careful not to touch the metal portion of the tool.
17
Now disconnect the power cord wire connecter.
18
Remove the screw securing the grounding wire.
19
With the grounding wire released, you can fully remove the old cord.
20
Install the new power cord by first connecting the wire connecter.
21
Secure the grounding wire to the base with the screw.
22
Position the power cord in the support bracket then reinstall the cabinet.
23
Make sure the tabs on the sides of the cabinet align with the frame.
24
Replace the screws to secure the cabinet.
25
Rest the microwave on its back panel.
26
Reinstall the bottom panel by first reconnecting the wire harness then secure the wires in the twist retainer.
27
Fully reposition the bottom panel and secure it with the screws.
28
Return the microwave to its upright position.
29
Make sure the charcoal filter is properly positioned then replace the grill by inserting the tabs into the slots in the frame.
30
Slide the grill to the right and rethread the mounting screws.
31
Now carefully reposition the microwave on the mounting bracket by hooking the back edge of the appliance on the bracket tabs.
32
Insert the power cord through the hole in the upper cabinet.
33
Lift the microwave up and secure the mounting bolts.
34
Plug the new power cord in.
35
Replace the turntable and support and your microwave oven should be ready for use.

Applicable Product Model

Microwave
Brand
Product Type
Product Diagram & Manuals
Parts Needed
Total$0.00

Related Articles & Videos