Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Samsung Dishwasher Drain Pump Hose Replacement #DD81-01502A

08:21
27k
42
This video provides step-by-step repair instructions for replacing the drain pump hose on a Samsung dishwasher. The most common reason for replacing the drain pump hose is the dishwasher leaking from its base.

All of the information for this drain pump hose replacement video is applicable to the following brands:
Samsung

Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers

Step By Step Instructions

1
To replace the drain pump hose in your dishwasher, you will need to uninstall the appliance first.
2
To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Use a phillips-head screwdriver to remove the screws securing the lower access panel.
5
Remove the panel.
6
Use a 5/8th inch wrench to help unthread the water supply line from the inlet valve be prepared for some water to spill.
7
Next, unthread the screw securing the junction box cover. Then pull the cover off.
8
Note the location of the wires then untwist the wire nuts to disconnect the wires.
9
Unthread the strain relief nut and detach the strain relief from the junction box.
10
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
11
Open the dishwasher door and remove the mounting bracket screws.
12
To move the dishwasher, you may need to adjust the legs to lower the appliance. You can lower the rear leveling leg by using a 9/64th inch hex-head screwdriver to rotate the adjustment rod at the front clockwise.
13
Now, very carefully pull the dishwasher away from the cabinet.
14
Tip the dishwasher back so it rests on its rear panel.
15
Use the phillips-head screwdriver to unthread the screws securing the bottom access panel.
16
Pull the panel forward disconnect the leak sensor wire connecter and set the panel aside.
17
Release the spring clamp securing the drain pump hose to the pump and pull the hose off.
18
Next, unthread the screws securing the left side access panel.
19
Remove the panel.
20
Release the spring clamp securing the opposite end of the drain pump hose to the water panel. You may need to detach the drain hose to better access the pump hose spring clamp.
21
Slide off the old pump hose to fully remove it.
22
Prepare the new drain pump hose for installation by transferring the spring clamps from the old hose to the new one.
23
Attach the shorter end of the pump hose to the water panel and secure it with the spring clamp.
24
Secure the drain hose to the panel if necessary.
25
Replace the side access panel and secure it with the screws.
26
Attach the longer end of the new pump hose to the port on the pump and secure the clamp.
27
Reconnect the leak sensor wire connecter.
28
Reposition the bottom access panel on the base and snap the retaining tabs into place.
29
Rethread the screws to secure.
30
Return the dishwasher to its upright position.
31
Make sure the drain hose is accessible through the cabinet wall and that the water supply and power supply lines are positioned in their respective channels in the dishwasher base then gently slide the dishwasher back into the cabinet.
32
Adjust the leveling legs if necessary.
33
Replace the screws to secure the mounting brackets to the cabinet or countertop.
34
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
35
Make sure the hose is elevated above the connection point.
36
Fully position the wire strain relief in the junction box and secure the strain relief nut.
37
Connect the wires using the wire nuts.
38
Align the cover and replace the screw to secure.
39
Reconnect the water supply line to the inlet valve.
40
Replace the lower access panel and secure it with the screws.
41
With the repair completed turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain pump hose on a Samsung dishwasher. The most common reason for replacing the drain pump hose is the dishwasher leaking from its base.

All of the information for this drain pump hose replacement video is applicable to the following brands:
Samsung

Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
Step-By-Step Instructions
1
To replace the drain pump hose in your dishwasher, you will need to uninstall the appliance first.
2
To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Use a phillips-head screwdriver to remove the screws securing the lower access panel.
5
Remove the panel.
6
Use a 5/8th inch wrench to help unthread the water supply line from the inlet valve be prepared for some water to spill.
7
Next, unthread the screw securing the junction box cover. Then pull the cover off.
8
Note the location of the wires then untwist the wire nuts to disconnect the wires.
9
Unthread the strain relief nut and detach the strain relief from the junction box.
10
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
11
Open the dishwasher door and remove the mounting bracket screws.
12
To move the dishwasher, you may need to adjust the legs to lower the appliance. You can lower the rear leveling leg by using a 9/64th inch hex-head screwdriver to rotate the adjustment rod at the front clockwise.
13
Now, very carefully pull the dishwasher away from the cabinet.
14
Tip the dishwasher back so it rests on its rear panel.
15
Use the phillips-head screwdriver to unthread the screws securing the bottom access panel.
16
Pull the panel forward disconnect the leak sensor wire connecter and set the panel aside.
17
Release the spring clamp securing the drain pump hose to the pump and pull the hose off.
18
Next, unthread the screws securing the left side access panel.
19
Remove the panel.
20
Release the spring clamp securing the opposite end of the drain pump hose to the water panel. You may need to detach the drain hose to better access the pump hose spring clamp.
21
Slide off the old pump hose to fully remove it.
22
Prepare the new drain pump hose for installation by transferring the spring clamps from the old hose to the new one.
23
Attach the shorter end of the pump hose to the water panel and secure it with the spring clamp.
24
Secure the drain hose to the panel if necessary.
25
Replace the side access panel and secure it with the screws.
26
Attach the longer end of the new pump hose to the port on the pump and secure the clamp.
27
Reconnect the leak sensor wire connecter.
28
Reposition the bottom access panel on the base and snap the retaining tabs into place.
29
Rethread the screws to secure.
30
Return the dishwasher to its upright position.
31
Make sure the drain hose is accessible through the cabinet wall and that the water supply and power supply lines are positioned in their respective channels in the dishwasher base then gently slide the dishwasher back into the cabinet.
32
Adjust the leveling legs if necessary.
33
Replace the screws to secure the mounting brackets to the cabinet or countertop.
34
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
35
Make sure the hose is elevated above the connection point.
36
Fully position the wire strain relief in the junction box and secure the strain relief nut.
37
Connect the wires using the wire nuts.
38
Align the cover and replace the screw to secure.
39
Reconnect the water supply line to the inlet valve.
40
Replace the lower access panel and secure it with the screws.
41
With the repair completed turn the water supply back on as well as the power and your dishwasher should be ready for use.

Applicable Product Model

Dishwasher
Brand
Product Type
Model
Subtype
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$21.30
Total$0.00

Related Articles & Videos