Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Frigidaire Dishwasher Door Strike Replacement #5304475600

06:31
986
0
This video provides step-by-step instructions for replacing the door strike on Frigidaire dishwashers. The most common reason for replacing the door strike is the door not staying shut.

All of the information in this door strike replacement video is applicable to the following brands: Frigidaire

Tools used: 5/8 inch wrench, phillips head screwdriver

Step By Step Instructions

1
To replace the door strike on your dishwasher, you will need to pull the dishwasher a few inches away from the cabinet.
2
If the water supply and power supply lines do not provide enough slack to do this, you will need to fully uninstall the appliance. To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Use a 5/8th inch wrench to unthread the water supply line fitting from the shut-off valve – be prepared for some water to spill.
5
Use a phillips-head screwdriver to unthread the screws to release the lower access panel.
6
Unthread the screws securing the inner access panel.
7
Lift up the panel to detach.
8
Remove the nut and bolt securing the grounding wire to fully remove the panel.
9
Next, unthread the screw securing the junction box cover. Then pull the cover off.
10
Note the location of the wires then untwist the wire nuts to disconnect the wires.
11
Unthread the wire strain relief nut and detach the strain relief from the junction box.
12
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
13
Open the dishwasher door and remove the mounting bracket screws.
14
To move the dishwasher, you may need to adjust the front legs to lower the appliance.
15
Now, very carefully pull the dishwasher away from the cabinet.
16
Open the dishwasher door and use the phillips-head screwdriver to unthread the screw securing the door strike then slide out the old strike.
17
Install the new door strike by inserting it into the door frame then thread the screw to secure.
18
Make sure the drain hose and water supply line are accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
19
Adjust the leveling legs if necessary.
20
Replace the screws to secure the mounting brackets to the cabinet or countertop.
21
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
22
Make sure the hose is elevated above the connection point.
23
Fully position the wire strain relief in the junction box and secure the strain relief nut.
24
Connect the wires using the wire nuts.
25
Align the cover and replace the screw to secure.
26
Secure the grounding wire to the inner access panel with the nut and bolt.
27
Set the panel in place and rethread the screws to secure.
28
Realign the outer access panel and secure it with the screws.
29
Feed the water supply line through the cabinet and reattach it to the shut-off valve.
30
With the repair completed turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing the door strike on Frigidaire dishwashers. The most common reason for replacing the door strike is the door not staying shut.

All of the information in this door strike replacement video is applicable to the following brands: Frigidaire

Tools used: 5/8 inch wrench, phillips head screwdriver
Step-By-Step Instructions
1
To replace the door strike on your dishwasher, you will need to pull the dishwasher a few inches away from the cabinet.
2
If the water supply and power supply lines do not provide enough slack to do this, you will need to fully uninstall the appliance. To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Use a 5/8th inch wrench to unthread the water supply line fitting from the shut-off valve – be prepared for some water to spill.
5
Use a phillips-head screwdriver to unthread the screws to release the lower access panel.
6
Unthread the screws securing the inner access panel.
7
Lift up the panel to detach.
8
Remove the nut and bolt securing the grounding wire to fully remove the panel.
9
Next, unthread the screw securing the junction box cover. Then pull the cover off.
10
Note the location of the wires then untwist the wire nuts to disconnect the wires.
11
Unthread the wire strain relief nut and detach the strain relief from the junction box.
12
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
13
Open the dishwasher door and remove the mounting bracket screws.
14
To move the dishwasher, you may need to adjust the front legs to lower the appliance.
15
Now, very carefully pull the dishwasher away from the cabinet.
16
Open the dishwasher door and use the phillips-head screwdriver to unthread the screw securing the door strike then slide out the old strike.
17
Install the new door strike by inserting it into the door frame then thread the screw to secure.
18
Make sure the drain hose and water supply line are accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
19
Adjust the leveling legs if necessary.
20
Replace the screws to secure the mounting brackets to the cabinet or countertop.
21
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
22
Make sure the hose is elevated above the connection point.
23
Fully position the wire strain relief in the junction box and secure the strain relief nut.
24
Connect the wires using the wire nuts.
25
Align the cover and replace the screw to secure.
26
Secure the grounding wire to the inner access panel with the nut and bolt.
27
Set the panel in place and rethread the screws to secure.
28
Realign the outer access panel and secure it with the screws.
29
Feed the water supply line through the cabinet and reattach it to the shut-off valve.
30
With the repair completed turn the water supply back on as well as the power and your dishwasher should be ready for use.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$21.30
Total$0.00

Related Articles & Videos