Electrolux Electric Dryer Outlet Duct Thermal Fuse #134711401

07:46
11k
24
This video provides step-by-step instructions for replacing the outlet duct thermal fuse on Electrolux electric dryers. The most common reason for replacing the thermal fuse is if the dryer wont't run or runs too long.

Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver

All of the information in this thermal fuse replacement video is applicable to the following brands: Electrolux

Step By Step Instructions

1
Before you replace the outlet duct thermal fuse in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel mounting brackets to the frame.
5
With the screws removed, lift the panel up and use a small flat-head screwdriver to depress the retaining tab to release the wire connecter.
6
Open the dryer door and unthread the two screws on the front panel securing the lint filter housing cover.
7
Lift and support the dryer then unthread the bottom front panel mounting screws.
8
With the screws unthreaded, remove the support and unthread the top front panel mounting screws.
9
Lift the panel up and out.
10
Disconnect the door switch wire connecter to fully remove the front panel.
11
Now disconnect both the drum light wire connecter and the user control board wire connecter from the main control board.
12
Next, unthread the control board support bracket screws and detach the bracket from the front bulkhead.
13
Unthread the lower bulkhead mounting screws.
14
Carefully lift the front bulkhead up to detach it from the frame.
15
Support the main control board bracket.
16
Reach under the drum and unthread the belt from the pulley and motor shaft.
17
You can use the belt to help lift out the drum.
18
Now disconnect the wires from the thermal fuse.
19
Unthread the screws securing the fuse and remove the old component.
20
Install the new thermal fuse by aligning it on the outlet duct then thread and tighten the screws to secure.
21
Connect the wires to the terminals.
22
Reinstall the drum by positioning it on the rear rollers.
23
Loop the belt on the pulley and motor shaft in a zig-zag formation.
24
Rotate the drum to help align the belt.
25
Reinstall the front bulkhead by inserting the tabs into the slots in the frame as you align the drum on the front rollers.
26
Thread and tighten the lower bulkhead mounting screws.
27
Detach the support from the main control board bracket and hook the bracket onto the bulkhead.
28
Replace the screws.
29
Reconnect the user control board wire connecter as well as the drum light wire connecter.
30
Reinstall the front panel by first reconnecting the door switch wire connecter.
31
Now hook the front panel tabs on the slots in the frame.
32
Replace the panel mounting screws on top.
33
Lift and support the dryer to replace the bottom mounting screws.
34
Thread and tighten the two screws to secure the lint filter housing cover to the front panel.
35
Connect the wire connecter to the user control board.
36
Reposition the control panel and replace the screws to secure the brackets.
37
Realign the main top and slide it into place.
38
Rethread the screws in the back.
39
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the outlet duct thermal fuse on Electrolux electric dryers. The most common reason for replacing the thermal fuse is if the dryer wont't run or runs too long.

Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver

All of the information in this thermal fuse replacement video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Before you replace the outlet duct thermal fuse in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel mounting brackets to the frame.
5
With the screws removed, lift the panel up and use a small flat-head screwdriver to depress the retaining tab to release the wire connecter.
6
Open the dryer door and unthread the two screws on the front panel securing the lint filter housing cover.
7
Lift and support the dryer then unthread the bottom front panel mounting screws.
8
With the screws unthreaded, remove the support and unthread the top front panel mounting screws.
9
Lift the panel up and out.
10
Disconnect the door switch wire connecter to fully remove the front panel.
11
Now disconnect both the drum light wire connecter and the user control board wire connecter from the main control board.
12
Next, unthread the control board support bracket screws and detach the bracket from the front bulkhead.
13
Unthread the lower bulkhead mounting screws.
14
Carefully lift the front bulkhead up to detach it from the frame.
15
Support the main control board bracket.
16
Reach under the drum and unthread the belt from the pulley and motor shaft.
17
You can use the belt to help lift out the drum.
18
Now disconnect the wires from the thermal fuse.
19
Unthread the screws securing the fuse and remove the old component.
20
Install the new thermal fuse by aligning it on the outlet duct then thread and tighten the screws to secure.
21
Connect the wires to the terminals.
22
Reinstall the drum by positioning it on the rear rollers.
23
Loop the belt on the pulley and motor shaft in a zig-zag formation.
24
Rotate the drum to help align the belt.
25
Reinstall the front bulkhead by inserting the tabs into the slots in the frame as you align the drum on the front rollers.
26
Thread and tighten the lower bulkhead mounting screws.
27
Detach the support from the main control board bracket and hook the bracket onto the bulkhead.
28
Replace the screws.
29
Reconnect the user control board wire connecter as well as the drum light wire connecter.
30
Reinstall the front panel by first reconnecting the door switch wire connecter.
31
Now hook the front panel tabs on the slots in the frame.
32
Replace the panel mounting screws on top.
33
Lift and support the dryer to replace the bottom mounting screws.
34
Thread and tighten the two screws to secure the lint filter housing cover to the front panel.
35
Connect the wire connecter to the user control board.
36
Reposition the control panel and replace the screws to secure the brackets.
37
Realign the main top and slide it into place.
38
Rethread the screws in the back.
39
With the repair completed plug the power cord back in and your dryer should be ready for use.

Applicable Product Model

Dryer
Brand
Product Type
Model
Subtype
Electric
Product Diagram & Manuals
Parts Needed
Total$0.00

Related Articles & Videos

00:00
0
0
Part Testing
Dryer Not Heating? Thermal Fuse Testing
03:43
30k
78
How This Part Works
Thermal Fuse Replacement
09:25
148k
674
Part Replacement
Electrolux Electric Dryer Replace Heating Element #137114000
07:04
150k
297
Part Replacement
Electrolux Electric Drive Belt Replacement #134719300