Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Electrolux Electric Dryer Inlet Mist Valve Replacement #137544800

05:55
7.6k
18
This video provides step-by-step instructions for replacing the inlet mist valve on Electrolux electric dryers. The most common reason for replacing the mist valve is if the steam feature does not function properly.

Parts used: #2 square bit, Phillips head screwdriver, flat head screwdriver

All of the information in this inlet mist valve replacement video is applicable to the following brands: Electrolux

Step By Step Instructions

1
Before you replace the water inlet mist valve in your dryer be sure to unplug the power cord
2
Close the water supply valve.
3
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
4
Slide the main top back and lift it up to remove.
5
Next, remove the screws to release the main top mounting bracket.
6
Remove the water supply line from the inlet valve – be prepared for some water to spill.
7
Now remove the screw to release the rear access panel.
8
Note the orientation of the power cord wires on the terminal block then use a quarter-inch socket or a phillips-head screwdriver to unthread the screws to disconnect the wires.
9
Now remove all of the screws securing the rear panel.
10
Set the rear panel aside.
11
Disconnect the water inlet mist valve wire harness.
12
Depress the locking ring to detach the water line.
13
Next, unthread the mounting screws and remove the old valve.
14
Install the new water inlet mist valve by inserting it in the rear bulkhead then thread and tighten the screws to secure.
15
Connect the water line to the new valve as well as the wire harness.
16
Reposition the rear panel then thread and tighten the screws to secure.
17
Note that the longer screw should be used to secure the panel above the exhaust vent.
18
Connect the power cord wires to the appropriate terminals on the terminal block and secure them with the screws.
19
Replace the rear access panel and secure it with the screw.
20
Realign the main top mounting bracket and replace the screws to secure.
21
Attach the water supply line to the inlet valve.
22
Realign the main top and slide it into place.
23
Rethread the screws in the back.
24
With the repair completed reopen the water supply valve plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the inlet mist valve on Electrolux electric dryers. The most common reason for replacing the mist valve is if the steam feature does not function properly.

Parts used: #2 square bit, Phillips head screwdriver, flat head screwdriver

All of the information in this inlet mist valve replacement video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Before you replace the water inlet mist valve in your dryer be sure to unplug the power cord
2
Close the water supply valve.
3
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
4
Slide the main top back and lift it up to remove.
5
Next, remove the screws to release the main top mounting bracket.
6
Remove the water supply line from the inlet valve – be prepared for some water to spill.
7
Now remove the screw to release the rear access panel.
8
Note the orientation of the power cord wires on the terminal block then use a quarter-inch socket or a phillips-head screwdriver to unthread the screws to disconnect the wires.
9
Now remove all of the screws securing the rear panel.
10
Set the rear panel aside.
11
Disconnect the water inlet mist valve wire harness.
12
Depress the locking ring to detach the water line.
13
Next, unthread the mounting screws and remove the old valve.
14
Install the new water inlet mist valve by inserting it in the rear bulkhead then thread and tighten the screws to secure.
15
Connect the water line to the new valve as well as the wire harness.
16
Reposition the rear panel then thread and tighten the screws to secure.
17
Note that the longer screw should be used to secure the panel above the exhaust vent.
18
Connect the power cord wires to the appropriate terminals on the terminal block and secure them with the screws.
19
Replace the rear access panel and secure it with the screw.
20
Realign the main top mounting bracket and replace the screws to secure.
21
Attach the water supply line to the inlet valve.
22
Realign the main top and slide it into place.
23
Rethread the screws in the back.
24
With the repair completed reopen the water supply valve plug the power cord back in and your dryer should be ready for use.

Applicable Product Model

Dryer
Brand
Product Type
Model
Subtype
Electric
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$8.99
Total$0.00

Related Articles & Videos