Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Electrolux Washer Motor Control Board Replacement #134618211

07:00
20k
38
This video provides step-by-step repair instructions for replacing the motor control board on an Electrolux washing machine. The most common reason for replacing the control board is if the washer tub will not spin.

All of the information for this motor control board replacement video is applicable to the following brands:
Electrolux

Tools needed: phillips head screwdriver, #2 square bit, T-20 Torx bit, needle nose pliers

Step By Step Instructions

1
Before you replace the motor control board in your washer be sure to unplug the power cord
2
Close the water supply valves.
3
Remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
4
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
5
Slide the main top back and lift it up to remove.
6
Next, unthread the screws securing the vibration dampener.
7
Lift off the block.
8
Disconnect the power cord wire connecter detach the grounding wire from the rear panel and release the wire retainer.
9
Unthread the mounting screw securing the drain hose retainer and remove the retainer.
10
Next, remove the screws securing the main top mounting bracket.
11
Set the bracket aside.
12
Unthread the screw securing the rear panel to the motor control board.
13
Now use a t-20 torx bit to unthread the remaining screws securing the rear panel.
14
Detach the panel.
15
Use the number two square bit or the phillips-head screwdriver to loosen the mounting screw securing the motor control board.
16
Slide the control board out.
17
Detach the cover and note the orientation of the wires connected to the board.
18
Disconnect the wires.
19
Use needle-nose pliers to detach the wire retainers from the old housing.
20
Install the new motor control board by connecting all of the wires to the appropriate terminals.
21
Snap the wire retainers into the housing.
22
Position the new board on the base and tighten the mounting screw to secure.
23
Align the cover and snap it into place.
24
Reposition the rear panel.
25
Thread and tighten all of the mounting screws except for the two top screws on the back.
26
Realign the main top support bracket and secure it with the screws.
27
Reconnect the power cord wire connecter Attach the grounding wire to the rear panel and snap the wire retainer into place.
28
Realign the drain hose retainer and replace the mounting screw.
29
Reposition the vibration dampener then thread and tighten the screws to secure.
30
Realign the main top and slide it into place.
31
Rethread the screws in the back.
32
Reattach the hot and cold water supply lines to the inlet valve.
33
With the repair completed reopen the water supply valves plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the motor control board on an Electrolux washing machine. The most common reason for replacing the control board is if the washer tub will not spin.

All of the information for this motor control board replacement video is applicable to the following brands:
Electrolux

Tools needed: phillips head screwdriver, #2 square bit, T-20 Torx bit, needle nose pliers
Step-By-Step Instructions
1
Before you replace the motor control board in your washer be sure to unplug the power cord
2
Close the water supply valves.
3
Remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
4
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
5
Slide the main top back and lift it up to remove.
6
Next, unthread the screws securing the vibration dampener.
7
Lift off the block.
8
Disconnect the power cord wire connecter detach the grounding wire from the rear panel and release the wire retainer.
9
Unthread the mounting screw securing the drain hose retainer and remove the retainer.
10
Next, remove the screws securing the main top mounting bracket.
11
Set the bracket aside.
12
Unthread the screw securing the rear panel to the motor control board.
13
Now use a t-20 torx bit to unthread the remaining screws securing the rear panel.
14
Detach the panel.
15
Use the number two square bit or the phillips-head screwdriver to loosen the mounting screw securing the motor control board.
16
Slide the control board out.
17
Detach the cover and note the orientation of the wires connected to the board.
18
Disconnect the wires.
19
Use needle-nose pliers to detach the wire retainers from the old housing.
20
Install the new motor control board by connecting all of the wires to the appropriate terminals.
21
Snap the wire retainers into the housing.
22
Position the new board on the base and tighten the mounting screw to secure.
23
Align the cover and snap it into place.
24
Reposition the rear panel.
25
Thread and tighten all of the mounting screws except for the two top screws on the back.
26
Realign the main top support bracket and secure it with the screws.
27
Reconnect the power cord wire connecter Attach the grounding wire to the rear panel and snap the wire retainer into place.
28
Realign the drain hose retainer and replace the mounting screw.
29
Reposition the vibration dampener then thread and tighten the screws to secure.
30
Realign the main top and slide it into place.
31
Rethread the screws in the back.
32
Reattach the hot and cold water supply lines to the inlet valve.
33
With the repair completed reopen the water supply valves plug the power cord back in and your washer should be ready for use.

Applicable Product Model

Washing Machine
Brand
Product Type
Model
Subtype
Front Loading
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$8.99
Cleaner
Cleaner
$18.71
Cleaner
Cleaner
$22.37
Total$0.00

Related Articles & Videos