Whirlpool Gas Range Replace Propane Orifice Kit #W10619560

05:05
227k
992
This video provides step-by-step instructions for installing the propane orifice kit on a Whirlpool gas range.

All of the information in this kit replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Tools used: phillips head screwdriver, pliers, 3/8 inch nut driver

Step By Step Instructions

1
Before you install the propane orifice kit components in your range unplug the power cord
2
Shut off the gas supply.
3
Carefully lift off the burner grates and remove the right front burner cap.
4
Insert a 7mm nut driver through the hole in the burner head and use it to unthread the natural gas orifice from the holder. You can now install the appropriate propane orifice the front burner orifices use a yellow and orange color coding.
5
Thread the new orifice into the holder then tighten.
6
Replace the burner cap.
7
Repeat this procedure for the left front burner orifice.
8
To replace the rear and center burner orifices, you will need to use a phillips-head screwdriver to unthread the screws securing the burner heads and set the heads aside.
9
Use pliers to secure the orifice holders as you unthread the old orifice and replace it with the new one.
10
The left rear and center orifices are color-coded yellow and black
11
The color coding for the right rear orifice is yellow and white.
12
With the orifice installed, realign the burner head and secure it with the screws.
13
Replace the burner caps and reposition the grates.
14
Next, open the oven door and remove the racks.
15
Lift the lower access panel up from the rear and slide it back to remove.
16
Unthread the mounting screw securing the burner tube.
17
Detach the tube.
18
Place a small piece of electrical tape over the end of a 3/8th inch nut driver then use the driver to unthread the natural gas orifice from the safety valve tube.
19
Thread the propane oven orifice into the safety valve tube and tighten.
20
Reposition the burner tube and replace the mounting screw to secure. Be aware you may need to adjust the air shutter on the burner tube to achieve a proper flame.
21
Now use a large flat-head screwdriver to unthread the regulator cap.
22
Unthread the spring tension pin and thread the opposite end of the pin into the cap.
23
Confirm that the washer is in place then thread the cap back into the regulator and tighten.
24
Replace the lower access panel by inserting the front edge under the oven door frame then push the rear of the panel into place.
25
Reinstall the oven racks.
26
With the repair completed turn the gas supply back on plug the power cord back in and your range should be ready for use.
Description
This video provides step-by-step instructions for installing the propane orifice kit on a Whirlpool gas range.

All of the information in this kit replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Tools used: phillips head screwdriver, pliers, 3/8 inch nut driver
Step-By-Step Instructions
1
Before you install the propane orifice kit components in your range unplug the power cord
2
Shut off the gas supply.
3
Carefully lift off the burner grates and remove the right front burner cap.
4
Insert a 7mm nut driver through the hole in the burner head and use it to unthread the natural gas orifice from the holder. You can now install the appropriate propane orifice the front burner orifices use a yellow and orange color coding.
5
Thread the new orifice into the holder then tighten.
6
Replace the burner cap.
7
Repeat this procedure for the left front burner orifice.
8
To replace the rear and center burner orifices, you will need to use a phillips-head screwdriver to unthread the screws securing the burner heads and set the heads aside.
9
Use pliers to secure the orifice holders as you unthread the old orifice and replace it with the new one.
10
The left rear and center orifices are color-coded yellow and black
11
The color coding for the right rear orifice is yellow and white.
12
With the orifice installed, realign the burner head and secure it with the screws.
13
Replace the burner caps and reposition the grates.
14
Next, open the oven door and remove the racks.
15
Lift the lower access panel up from the rear and slide it back to remove.
16
Unthread the mounting screw securing the burner tube.
17
Detach the tube.
18
Place a small piece of electrical tape over the end of a 3/8th inch nut driver then use the driver to unthread the natural gas orifice from the safety valve tube.
19
Thread the propane oven orifice into the safety valve tube and tighten.
20
Reposition the burner tube and replace the mounting screw to secure. Be aware you may need to adjust the air shutter on the burner tube to achieve a proper flame.
21
Now use a large flat-head screwdriver to unthread the regulator cap.
22
Unthread the spring tension pin and thread the opposite end of the pin into the cap.
23
Confirm that the washer is in place then thread the cap back into the regulator and tighten.
24
Replace the lower access panel by inserting the front edge under the oven door frame then push the rear of the panel into place.
25
Reinstall the oven racks.
26
With the repair completed turn the gas supply back on plug the power cord back in and your range should be ready for use.

Applicable Product Model

Range/Stove/Oven
Brand
Product Type
Model
Subtype
Gas
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Total$0.00

Related Articles & Videos

06:54
106k
526
Part Replacement
Whirlpool Gas Stove Front Burner Valve Replacement #W10814916
03:08
108k
518
Part Replacement
Whirlpool Gas Oven Igniter Replacement #98005652
02:08
124k
322
Part Replacement
Whirlpool Gas Range Surface Igniter Replacement #W10515459
03:32
33k
115
Part Replacement
Whirlpool Gas Range Main Top Replacement #W10527866