Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Danby Dishwasher Replace Top Sprayer Connector #673001200018

06:04
1.5k
0
This video provides step-by-step repair instructions for replacing the top sprayer connector on a Danby dishwasher. The most common reason for replacing the connector is if no water is coming out of the top sprayer, or the dishwasher is leaking.

All of the information for this dishwasher connector replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, pliers

Step By Step Instructions

1
To replace the top sprayer connecter in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Now open the dishwasher door and pull the upper rack forward.
13
Unthread the nozzle counter-clockwise to remove.
14
Pull the sprayer connecter out.
15
Use pliers to release the clamp securing the hose to the connecter and pull the hose off.
16
Prepare the new top sprayer connecter for installation by transferring the o-ring from the old connecter to the new one.
17
Attach the hose and secure it with the clamp.
18
Position the connecter then thread on the nozzle to secure.
19
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
20
Adjust the leveling legs if necessary.
21
Replace the screws to secure the mounting brackets to the cabinet or countertop.
22
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
23
Make sure the hose is elevated above the connection point.
24
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
25
Connect the wires using the wire nuts.
26
Align the cover and replace the screw to secure.
27
Reconnect the water supply line to the inlet valve elbow fitting.
28
Realign the lower access panel and snap it into place.
29
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the top sprayer connector on a Danby dishwasher. The most common reason for replacing the connector is if no water is coming out of the top sprayer, or the dishwasher is leaking.

All of the information for this dishwasher connector replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, pliers
Step-By-Step Instructions
1
To replace the top sprayer connecter in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Now open the dishwasher door and pull the upper rack forward.
13
Unthread the nozzle counter-clockwise to remove.
14
Pull the sprayer connecter out.
15
Use pliers to release the clamp securing the hose to the connecter and pull the hose off.
16
Prepare the new top sprayer connecter for installation by transferring the o-ring from the old connecter to the new one.
17
Attach the hose and secure it with the clamp.
18
Position the connecter then thread on the nozzle to secure.
19
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
20
Adjust the leveling legs if necessary.
21
Replace the screws to secure the mounting brackets to the cabinet or countertop.
22
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
23
Make sure the hose is elevated above the connection point.
24
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
25
Connect the wires using the wire nuts.
26
Align the cover and replace the screw to secure.
27
Reconnect the water supply line to the inlet valve elbow fitting.
28
Realign the lower access panel and snap it into place.
29
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
O-Ring
O-Ring
$6.38
Total$0.00

Related Articles & Videos