Danby Dishwasher Power Switch Replacement #674000300089

03:41
5k
22
This video provides step-by-step repair instructions for replacing the power switch on a Danby dishwasher. The most common reason for replacing the switch is if the dishwasher will not operate at all.

All of the information for this dishwasher power switch replacement video is applicable to the following brands:
Danby

Tools needed: Phillip's head screwdriver, needle nose pliers

Step By Step Instructions

1
Before you replace the power switch on your dishwasher be sure to turn off the power to the appliance.
2
Open the dishwasher door and use a phillips-head screwdriver to unthread the mounting screws securing the outer door panel.
3
Slide the door panel down to remove.
4
Next, unthread the screws securing the control panel.
5
Detach the panel and note the location of the power switch wires.
6
You can use needle-nose pliers to help disconnect the wires.
7
Remove the two screws securing the power switch retaining bracket.
8
Slide off the bracket and pull the old power switch free of the panel.
9
You’re now ready to install the new power switch.
10
Hold the power button then align the new switch with the terminals positioned vertically and snap the switch into place.
11
Properly align the retaining bracket and replace the screws to secure.
12
Connect the wires to the appropriate terminals on the new switch.
13
Reposition the control panel on the inner door panel and rethread the screws to secure.
14
Replace the outer door panel by sliding the edges up behind the control panel.
15
Hold the panel in place as you rethread the mounting screws.
16
With the repair completed turn the power supply back on and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the power switch on a Danby dishwasher. The most common reason for replacing the switch is if the dishwasher will not operate at all.

All of the information for this dishwasher power switch replacement video is applicable to the following brands:
Danby

Tools needed: Phillip's head screwdriver, needle nose pliers
Step-By-Step Instructions
1
Before you replace the power switch on your dishwasher be sure to turn off the power to the appliance.
2
Open the dishwasher door and use a phillips-head screwdriver to unthread the mounting screws securing the outer door panel.
3
Slide the door panel down to remove.
4
Next, unthread the screws securing the control panel.
5
Detach the panel and note the location of the power switch wires.
6
You can use needle-nose pliers to help disconnect the wires.
7
Remove the two screws securing the power switch retaining bracket.
8
Slide off the bracket and pull the old power switch free of the panel.
9
You’re now ready to install the new power switch.
10
Hold the power button then align the new switch with the terminals positioned vertically and snap the switch into place.
11
Properly align the retaining bracket and replace the screws to secure.
12
Connect the wires to the appropriate terminals on the new switch.
13
Reposition the control panel on the inner door panel and rethread the screws to secure.
14
Replace the outer door panel by sliding the edges up behind the control panel.
15
Hold the panel in place as you rethread the mounting screws.
16
With the repair completed turn the power supply back on and your dishwasher should be ready for use.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
Button
Button
$341.83
Total$0.00

Related Articles & Videos

06:38
57k
86
Part Replacement
Danby Dishwasher Heating Element Replacement #674001100030
08:37
14k
48
Part Replacement
Danby Dishwasher Water Softener Dispenser #674000700018
06:14
8.2k
15
Part Replacement
Danby Dishwasher Temperature Sensor Replacement #674000900038
08:52
2.7k
10
Part Replacement
Danby Dishwasher Circulation Pump Replacement #674000600053