Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Danby Dishwasher Circulation Pump Replacement #674000600053

08:52
2.7k
10
This video provides step-by-step repair instructions for replacing the circulation pump on a Danby dishwasher. The most common reason for replacing the pump is if the dishwasher is not washing properly.

All of the information for this dishwasher circulation pump replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, 7mm wrench

Step By Step Instructions

1
To replace the circulation pump in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Remove the screw securing the circulation pump mounting bracket to the frame.
13
Tip the dishwasher back so it rests on its rear panel.
14
Pull the mounting bracket off of the circulation pump.
15
Break the pinch clamps securing the inlet and outlet hoses to the pump
16
Pull the hoses off to release the pump.
17
Cut the zip tie securing the circulation pump wires.
18
Disconnect the wires from the capacitor and the motor connecter then disconnect the grounding wire to fully remove the old pump.
19
You’re now ready to install the new circulation pump and capacitor
20
Transfer the cover from the old pump to the new one.
21
Use a 7mm socket and a phillips-head screwdriver to remove the nut and bolt securing the old capacitor.
22
Align the mounting bracket on the new capacitor position the assembly on the frame then secure it with the nut and bolt.
23
Connect the new pump wires to the capacitor.
24
Attach the grounding wire to the new pump and connect the wires to the motor connecter.
25
Secure the wires with a zip tie.
26
Slide new clamps onto the inlet and outlet hoses.
27
Attach the hoses to the appropriate ports on the pump then secure them with the clamps.
28
Align the mounting bracket on the new pump.
29
Return the dishwasher to its upright position.
30
Replace the screw to secure the pump mounting bracket to the frame.
31
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
32
Adjust the leveling legs if necessary.
33
Replace the screws to secure the mounting brackets to the cabinet or countertop.
34
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
35
Make sure the hose is elevated above the connection point.
36
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
37
Connect the wires using the wire nuts.
38
Align the cover and replace the screw to secure.
39
Reconnect the water supply line to the inlet valve elbow fitting.
40
Realign the lower access panel and snap it into place.
41
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the circulation pump on a Danby dishwasher. The most common reason for replacing the pump is if the dishwasher is not washing properly.

All of the information for this dishwasher circulation pump replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, 7mm wrench
Step-By-Step Instructions
1
To replace the circulation pump in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Remove the screw securing the circulation pump mounting bracket to the frame.
13
Tip the dishwasher back so it rests on its rear panel.
14
Pull the mounting bracket off of the circulation pump.
15
Break the pinch clamps securing the inlet and outlet hoses to the pump
16
Pull the hoses off to release the pump.
17
Cut the zip tie securing the circulation pump wires.
18
Disconnect the wires from the capacitor and the motor connecter then disconnect the grounding wire to fully remove the old pump.
19
You’re now ready to install the new circulation pump and capacitor
20
Transfer the cover from the old pump to the new one.
21
Use a 7mm socket and a phillips-head screwdriver to remove the nut and bolt securing the old capacitor.
22
Align the mounting bracket on the new capacitor position the assembly on the frame then secure it with the nut and bolt.
23
Connect the new pump wires to the capacitor.
24
Attach the grounding wire to the new pump and connect the wires to the motor connecter.
25
Secure the wires with a zip tie.
26
Slide new clamps onto the inlet and outlet hoses.
27
Attach the hoses to the appropriate ports on the pump then secure them with the clamps.
28
Align the mounting bracket on the new pump.
29
Return the dishwasher to its upright position.
30
Replace the screw to secure the pump mounting bracket to the frame.
31
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
32
Adjust the leveling legs if necessary.
33
Replace the screws to secure the mounting brackets to the cabinet or countertop.
34
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
35
Make sure the hose is elevated above the connection point.
36
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
37
Connect the wires using the wire nuts.
38
Align the cover and replace the screw to secure.
39
Reconnect the water supply line to the inlet valve elbow fitting.
40
Realign the lower access panel and snap it into place.
41
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$20.66
Total$0.00

Related Articles & Videos