Danby Dishwasher Drain Pump Replacement #674000600082

06:10
4.2k
8
This video provides step-by-step repair instructions for replacing the drain pump on a Danby dishwasher. The most common reason for replacing the pump is if the dishwasher is not draining properly.

All of the information for this dishwasher drain pump replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver

Step By Step Instructions

1
To replace the drain pump in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Tip the dishwasher back so it rests on its rear panel.
13
Disconnect the wires from the drain pump.
14
Unthread the mounting screws securing the pump.
15
Rotate the old pump counter-clockwise to remove.
16
Install the new drain pump by inserting it into the housing and rotating it clockwise to lock it into place.
17
Thread and tighten the mounting screws.
18
Connect the wires to the terminals on the new pump.
19
Return the dishwasher to its upright position.
20
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
21
Adjust the leveling legs if necessary.
22
Replace the screws to secure the mounting brackets to the cabinet or countertop.
23
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
24
Make sure the hose is elevated above the connection point.
25
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
26
Connect the wires using the wire nuts.
27
Align the cover and replace the screw to secure.
28
Reconnect the water supply line to the inlet valve elbow fitting.
29
Realign the lower access panel and snap it into place.
30
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain pump on a Danby dishwasher. The most common reason for replacing the pump is if the dishwasher is not draining properly.

All of the information for this dishwasher drain pump replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver
Step-By-Step Instructions
1
To replace the drain pump in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Tip the dishwasher back so it rests on its rear panel.
13
Disconnect the wires from the drain pump.
14
Unthread the mounting screws securing the pump.
15
Rotate the old pump counter-clockwise to remove.
16
Install the new drain pump by inserting it into the housing and rotating it clockwise to lock it into place.
17
Thread and tighten the mounting screws.
18
Connect the wires to the terminals on the new pump.
19
Return the dishwasher to its upright position.
20
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
21
Adjust the leveling legs if necessary.
22
Replace the screws to secure the mounting brackets to the cabinet or countertop.
23
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
24
Make sure the hose is elevated above the connection point.
25
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
26
Connect the wires using the wire nuts.
27
Align the cover and replace the screw to secure.
28
Reconnect the water supply line to the inlet valve elbow fitting.
29
Realign the lower access panel and snap it into place.
30
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.

Applicable Product Model

Parts Needed
Drain Pump
Drain Pump
$119.13
Recommended Tools and Accessories
Cleaner
Cleaner
$21.94
Total$0.00

Related Articles & Videos

06:38
57k
86
Part Replacement
Danby Dishwasher Heating Element Replacement #674001100030
08:37
14k
48
Part Replacement
Danby Dishwasher Water Softener Dispenser #674000700018
03:41
5k
22
Part Replacement
Danby Dishwasher Power Switch Replacement #674000300089
06:14
8.2k
15
Part Replacement
Danby Dishwasher Temperature Sensor Replacement #674000900038