Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Danby Dishwasher Heating Element Replacement #674001100030

06:38
57k
86
This video provides step-by-step repair instructions for replacing the heating element on a Danby dishwasher. The most common reason for replacing the element is if the water entering the dishwasher is not getting hot enough, causing the dishes to not wash properly.

All of the information for this dishwasher heating element replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver

Step By Step Instructions

1
To replace the heating element in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Now tip the dishwasher back so it rests on its rear panel.
13
Break the pinch clamps securing the inlet and outlet hoses to the heating element.
14
Pull the hoses off.
15
Disconnect the wire connecters along with the grounding wire from the old element.
16
Install the new heating element by connecting the wire connecters to the appropriate terminals as well as the grounding wire.
17
Slide new clamps on the inlet and outlet hoses.
18
Attach the hoses to the appropriate ports on the heating element then secure them with the clamps.
19
Return the dishwasher to its upright position.
20
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
21
Adjust the leveling legs if necessary.
22
Replace the screws to secure the mounting brackets to the cabinet or countertop.
23
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
24
Make sure the hose is elevated above the connection point.
25
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
26
Connect the wires using the wire nuts.
27
Align the cover and replace the screw to secure.
28
Reconnect the water supply line to the inlet valve elbow fitting.
29
Realign the lower access panel and snap it into place.
30
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the heating element on a Danby dishwasher. The most common reason for replacing the element is if the water entering the dishwasher is not getting hot enough, causing the dishes to not wash properly.

All of the information for this dishwasher heating element replacement video is applicable to the following brands:
Danby

Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver
Step-By-Step Instructions
1
To replace the heating element in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Now tip the dishwasher back so it rests on its rear panel.
13
Break the pinch clamps securing the inlet and outlet hoses to the heating element.
14
Pull the hoses off.
15
Disconnect the wire connecters along with the grounding wire from the old element.
16
Install the new heating element by connecting the wire connecters to the appropriate terminals as well as the grounding wire.
17
Slide new clamps on the inlet and outlet hoses.
18
Attach the hoses to the appropriate ports on the heating element then secure them with the clamps.
19
Return the dishwasher to its upright position.
20
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
21
Adjust the leveling legs if necessary.
22
Replace the screws to secure the mounting brackets to the cabinet or countertop.
23
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
24
Make sure the hose is elevated above the connection point.
25
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
26
Connect the wires using the wire nuts.
27
Align the cover and replace the screw to secure.
28
Reconnect the water supply line to the inlet valve elbow fitting.
29
Realign the lower access panel and snap it into place.
30
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$20.66
Total$0.00

Related Articles & Videos