1-800-269-2609 24/7
Orders placed by 8:00 p.m. ET Monday through Friday will ship the same day.
Frigidaire Refrigerator Damper Control Assembly #241518501
Skill Level
Total Parts Cost
$177.80Estimated Savings
$112.5003:48
24k
64
- Description
This video provides step-by-step repair instructions for replacing the damper control assembly on a Frigidaire refrigerator. The most common reason for replacing the damper is if the refrigerator is not cooling properly.
All of the information for this refrigerator damper replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, putty knife
All of the information for this refrigerator damper replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, putty knife
Step By Step Instructions
1
Before you replace the damper control assembly in your refrigerator be sure to unplug the power cord.
2
Pull the deli drawer out lift up and fully remove.
3
Next, pull both crisper drawers out and lift up to detach them from the tracks.
4
Carefully remove the lower glass shelf insert.
5
Rotate the front and rear glass support rails up to remove.
6
Lift up the air duct cover to detach.
7
Use a phillips-head screwdriver or a number two square drive bit to unthread the screws to release the damper cover.
8
Use a putty knife to help pry out the insulation block.
9
Lift up the damper control assembly and pull it out of the housing.
10
Depress the retaining tab to disconnect the wire connecter.
11
Before you install the new damper control assembly we recommend applying a new seal to the damper inlet opening.
12
Connect the wire connecter.
13
Align the damper control assembly in the housing and push down.
14
With the arrow pointing up, reinsert the insulation block.
15
Realign the damper cover and secure it with the screws.
16
Reposition the air duct cover and snap it into place.
17
Replace the front and rear glass shelf support rails.
18
Carefully reposition the glass shelf insert.
19
Replace the crisper drawers by aligning them on the tracks and pushing them closed.
20
Pull both deli drawer slide rails out.
21
Reinstall the deli drawer by positioning the rear of the drawer first then pull the rails forward until the drawer locks into place.
22
With the repair completed plug the power cord back in and your refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the damper control assembly on a Frigidaire refrigerator. The most common reason for replacing the damper is if the refrigerator is not cooling properly.
All of the information for this refrigerator damper replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, putty knife
All of the information for this refrigerator damper replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, putty knife
Step-By-Step Instructions
1
Before you replace the damper control assembly in your refrigerator be sure to unplug the power cord.
2
Pull the deli drawer out lift up and fully remove.
3
Next, pull both crisper drawers out and lift up to detach them from the tracks.
4
Carefully remove the lower glass shelf insert.
5
Rotate the front and rear glass support rails up to remove.
6
Lift up the air duct cover to detach.
7
Use a phillips-head screwdriver or a number two square drive bit to unthread the screws to release the damper cover.
8
Use a putty knife to help pry out the insulation block.
9
Lift up the damper control assembly and pull it out of the housing.
10
Depress the retaining tab to disconnect the wire connecter.
11
Before you install the new damper control assembly we recommend applying a new seal to the damper inlet opening.
12
Connect the wire connecter.
13
Align the damper control assembly in the housing and push down.
14
With the arrow pointing up, reinsert the insulation block.
15
Realign the damper cover and secure it with the screws.
16
Reposition the air duct cover and snap it into place.
17
Replace the front and rear glass shelf support rails.
18
Carefully reposition the glass shelf insert.
19
Replace the crisper drawers by aligning them on the tracks and pushing them closed.
20
Pull both deli drawer slide rails out.
21
Reinstall the deli drawer by positioning the rear of the drawer first then pull the rails forward until the drawer locks into place.
22
With the repair completed plug the power cord back in and your refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Damper Control Assembly
$177.80
Total$0.00
Related Articles & Videos
07:17
171k
699
Part Replacement
Frigidaire Refrigerator Replace Evaporator Fan Motor 241509402
04:13
112k
480
Part Replacement
Frigidaire Refrigerator Replace Water Inlet Valve #242253002
02:40
106k
324
Part Replacement
Frigidaire Refrigerator Replace Main Control Board #5304502779
02:14
94k
366
Part Replacement
Frigidaire Refrigerator User Interface Replacement #242058230
About Us
Start doing it yourself with the confidence that comes with 100+ years of experience. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right.
© 2023 RepairClinic.com1‑800‑269‑2609
