1-800-269-2609 24/7
Orders placed by 8:00 p.m. ET Monday through Friday will ship the same day.
Frigidaire Dishwasher Control Panel Replacement (part 5304520552)
Skill Level
Total Parts Cost
$82.72Estimated Savings
$112.5004:55
31k
137
- Description
This video provides step-by-step repair instructions for replacing the control panel on Frigidaire dishwasher model #FGID2466QF7A. The most common reason for replacing the panel is if the dishwasher won’t start.
All of the information for this control panel replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
All of the information for this control panel replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
Step By Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Control Panel Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
"Pull the retaining tabs back to release the two user interface boards, then disconnect the wire harness from the control board."
12
Pull the retaining tab back to detach the display board and then disconnect the wire harness.
13
Unthread the mounting screws to release the control board.
14
You’re now ready to prepare the new control panel for installation.
15
"Confirm that the seal is in place on the panel, then position the control board and thread the mounting screws."
16
Align the display board and snap it into place.
17
Connect the wire harness to the control board.
18
Slide the two user interface boards into place and connect the wire harness.
19
Secure the wires under the retaining clips.
20
Position the wiring grommet in the control board cover then snap the cover into place.
21
Thread the two mounting screws.
22
Realign the control panel assembly and secure it with the screws.
23
Reinstall the outer door panel by aligning it on the inner panel then slide up.
24
Thread the four mounting screws to secure.
25
Turn the power supply back on.
26
Congrats! Your dishwasher is ready for use.
Description
This video provides step-by-step repair instructions for replacing the control panel on Frigidaire dishwasher model #FGID2466QF7A. The most common reason for replacing the panel is if the dishwasher won’t start.
All of the information for this control panel replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
All of the information for this control panel replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
Step-By-Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Control Panel Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
"Pull the retaining tabs back to release the two user interface boards, then disconnect the wire harness from the control board."
12
Pull the retaining tab back to detach the display board and then disconnect the wire harness.
13
Unthread the mounting screws to release the control board.
14
You’re now ready to prepare the new control panel for installation.
15
"Confirm that the seal is in place on the panel, then position the control board and thread the mounting screws."
16
Align the display board and snap it into place.
17
Connect the wire harness to the control board.
18
Slide the two user interface boards into place and connect the wire harness.
19
Secure the wires under the retaining clips.
20
Position the wiring grommet in the control board cover then snap the cover into place.
21
Thread the two mounting screws.
22
Realign the control panel assembly and secure it with the screws.
23
Reinstall the outer door panel by aligning it on the inner panel then slide up.
24
Thread the four mounting screws to secure.
25
Turn the power supply back on.
26
Congrats! Your dishwasher is ready for use.
Applicable Product Model
Related Articles & Videos
07:11
34k
192
Part Replacement
Frigidaire Dishwasher Circulation Pump & Motor Replacement (part 154853801)
02:56
46k
152
Part Replacement
Frigidaire Dishwasher Door Latch Replacement (part 5304516818)
01:08
46k
113
Part Replacement
Frigidaire Dishwasher Bottom Tank Gasket Replacement (part 5304500204)
00:48
30k
96
Part Replacement
Frigidaire Dishwasher Center Wash Arm Assembly Replacement (part 5304506740)
About Us
Start doing it yourself with the confidence that comes with 100+ years of experience. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right.
© 2023 RepairClinic.com1‑800‑269‑2609
