Frigidaire Dishwasher Valve-To-Tank Water Supply Tube Replacement (part 154446002)

06:27
416
0
This video provides step-by-step repair instructions for replacing the valve-to-tank water supply tube on Frigidaire dishwasher model #FGID2466QF7A.

All of the information for this valve-to-tank water supply tube replacement video is applicable to the following brands: Frigidaire & Electrolux

Tools needed: Quarter-inch socket, Phillips-head screwdriver, Channel-lock pliers, T-20 Torx bit, & a flathead screwdriver.

Step By Step Instructions

1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Valve-To-Tank Water Supply Tube Replacement
3
Tools & Assistance Needed
4
"You will need a quarter-inch socket or a phillips-head screwdriver, channel-lock pliers, a quarter-inch socket or a T-20 Torx bit and pliers for this procedure, and you may need assistance."
5
"Before you attempt this, be sure to turn off the power to the appliance."
6
Shut off the water supply valve.
7
"Using a quarter-inch socket or a phillips-head screwdriver, unthread the two mounting screws securing the lower access panels."
8
Set the panels aside.
9
Use channel-lock pliers to unthread the water supply line elbow fitting from the inlet valve - be prepared for some water to spill.
10
Use a quarter-inch socket or a T-20 Torx bit to unthread the screw to release the junction box cover.
11
"Note the orientation of the power wires, then untwist the wire nuts to disconnect the wires."
12
Unthread the screw to release the grounding wire.
13
Unthread the strain relief nut and detach the strain relief and power wires from the junction box.
14
Disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
15
"Unthread the mounting screws securing the dishwasher to the countertop, cabinet, or floor."
16
"To move the dishwasher, you may need to adjust the legs to lower the appliance."
17
Gently pull the dishwasher away from the cabinet.
18
Pull back the insulating blanket.
19
Use pliers to release the spring clamp so you can detach the old supply tube from the inlet valve.
20
Release the spring clamp to detach the tube from the fill cup.
21
Unhook the old tube from the retainers to fully remove.
22
Prepare the new valve-to-tank water supply tube for installation by sliding a spring clamp over the each end.
23
Attach one end to the inlet valve and secure it with the clamp.
24
Attach the opposite end to the fill cup.
25
Secure the new tube in the retainers and reposition the insulating blanket.
26
"Confirm that the end of the drain hose is accessible through the cabinet wall, then gently slide the dishwasher back into the cabinet."
27
Adjust the leveling legs if necessary.
28
"Rethread the screws to secure the appliance to the countertop, cabinet, or floor."
29
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
30
Make sure the hose is elevated above the connection point.
31
"Fully position the wires and strain relief in the junction box, then thread and tighten the strain relief nut."
32
Secure the grounding wire with the screw.
33
Join the black wires together and the white wires together and secure them with the wire nuts.
34
"With the wires positioned inside the junction box, realign the cover and rethread the screw to secure."
35
Reconnect the water supply line fitting to the inlet valve.
36
"Realign the two access panels, then thread the screws to secure."
37
"Turn the water supply back on, as well as the power."
38
Congrats! Your dishwasher is ready for use.
Description
This video provides step-by-step repair instructions for replacing the valve-to-tank water supply tube on Frigidaire dishwasher model #FGID2466QF7A.

All of the information for this valve-to-tank water supply tube replacement video is applicable to the following brands: Frigidaire & Electrolux

Tools needed: Quarter-inch socket, Phillips-head screwdriver, Channel-lock pliers, T-20 Torx bit, & a flathead screwdriver.
Step-By-Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Valve-To-Tank Water Supply Tube Replacement
3
Tools & Assistance Needed
4
"You will need a quarter-inch socket or a phillips-head screwdriver, channel-lock pliers, a quarter-inch socket or a T-20 Torx bit and pliers for this procedure, and you may need assistance."
5
"Before you attempt this, be sure to turn off the power to the appliance."
6
Shut off the water supply valve.
7
"Using a quarter-inch socket or a phillips-head screwdriver, unthread the two mounting screws securing the lower access panels."
8
Set the panels aside.
9
Use channel-lock pliers to unthread the water supply line elbow fitting from the inlet valve - be prepared for some water to spill.
10
Use a quarter-inch socket or a T-20 Torx bit to unthread the screw to release the junction box cover.
11
"Note the orientation of the power wires, then untwist the wire nuts to disconnect the wires."
12
Unthread the screw to release the grounding wire.
13
Unthread the strain relief nut and detach the strain relief and power wires from the junction box.
14
Disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
15
"Unthread the mounting screws securing the dishwasher to the countertop, cabinet, or floor."
16
"To move the dishwasher, you may need to adjust the legs to lower the appliance."
17
Gently pull the dishwasher away from the cabinet.
18
Pull back the insulating blanket.
19
Use pliers to release the spring clamp so you can detach the old supply tube from the inlet valve.
20
Release the spring clamp to detach the tube from the fill cup.
21
Unhook the old tube from the retainers to fully remove.
22
Prepare the new valve-to-tank water supply tube for installation by sliding a spring clamp over the each end.
23
Attach one end to the inlet valve and secure it with the clamp.
24
Attach the opposite end to the fill cup.
25
Secure the new tube in the retainers and reposition the insulating blanket.
26
"Confirm that the end of the drain hose is accessible through the cabinet wall, then gently slide the dishwasher back into the cabinet."
27
Adjust the leveling legs if necessary.
28
"Rethread the screws to secure the appliance to the countertop, cabinet, or floor."
29
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
30
Make sure the hose is elevated above the connection point.
31
"Fully position the wires and strain relief in the junction box, then thread and tighten the strain relief nut."
32
Secure the grounding wire with the screw.
33
Join the black wires together and the white wires together and secure them with the wire nuts.
34
"With the wires positioned inside the junction box, realign the cover and rethread the screw to secure."
35
Reconnect the water supply line fitting to the inlet valve.
36
"Realign the two access panels, then thread the screws to secure."
37
"Turn the water supply back on, as well as the power."
38
Congrats! Your dishwasher is ready for use.

Applicable Product Model

Dishwasher
Brand
Product Type
Model
Subtype
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$21.94
Total$0.00

Related Articles & Videos

07:11
34k
190
Part Replacement
Frigidaire Dishwasher Circulation Pump & Motor Replacement (part 154853801)
02:56
45k
150
Part Replacement
Frigidaire Dishwasher Door Latch Replacement (part 5304516818)
01:08
46k
113
Part Replacement
Frigidaire Dishwasher Bottom Tank Gasket Replacement (part 5304500204)
04:55
31k
136
Part Replacement
Frigidaire Dishwasher Control Panel Replacement (part 5304520552)