Toro Snowblower Fuel Hose Replacement 127-9403

08:23
2k
6
This video provides step-by-step repair instructions for replacing the fuel hose on a Toro snowblower.

All of the information for this video is applicable to the following brands:
Toro

Step By Step Instructions

1
Toro Snowblower - Model 38752
2
Snowblower Fuel Hose Replacement
3
Tools Needed
4
"You will need a 3/8th inch socket, a phillips-head screwdriver, an 8mm socket, a half-inch socket and a 10mm socket for this procedure."
5
Make sure the engine has cooled.
6
Be sure to perform this procedure with no fuel in the tank.
7
Use a 3/8th inch socket to unthread the three mounting bolts securing the chute handle and the chute itself.
8
Remove the assembly and detach the handle.
9
"Using a phillips-head screwdriver, unthread the screw to release the chute ring seal."
10
Unthread the two front housing mounting screws.
11
Unthread the three screws from the right side of the housing.
12
Use a 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
13
Unthread the screws to release the two retaining clamps holding the housing to the handle.
14
You can now fully remove the housing.
15
Use an 8mm socket to unthread the six bolts securing the muffler cover.
16
Use a half-inch socket to fully unthread the upper bolts securing the handle assembly.
17
Lower the handle to fully remove the muffler cover.
18
Detach the primer hose from the carburetor – be prepared for some fuel to spill.
19
Disconnect the wires from the key switch terminals.
20
Use a 10mm socket to unthread the nuts securing the control housing.
21
Pull the housing off of the mounting bolts.
22
"Use a 10mm socket to unthread the two nuts and an 8mm socket to unthread the screw securing the side access cover, then pull the cover off."
23
Use the 8mm socket to unthread the two mounting screws securing the trim and fuel tank.
24
Unthread the additional screw on the left securing the tank.
25
Release the clamp to detach the fuel hose and you can fully remove the tank.
26
Release the retaining clamp to detach the old fuel hose from the carburetor and remove both clamps.
27
Install the new fuel hose by feeding it under the speed control assembly.
28
Slide the two clamps over the appropriate ends.
29
"Attach the hose to the carburetor and secure it with the clamp, then attach the opposite end to the fuel tank and secure with the clamp."
30
Reposition the tank and thread the left-side screw.
31
Realign the trim and thread the screws; realign the side access cover and thread the screw and nuts to secure.
32
"Reposition the control housing, then thread and tighten the mounting nuts."
33
Connect the wires to the key switch terminals.
34
Reattach the primer hose to the carburetor.
35
Reposition the muffler cover and thread the six bolts to secure; reposition the handle assembly and rethread the upper bolts; reposition the housing.
36
Align the two retaining clamps and thread the screws to secure the housing to the handle.
37
Rethread the mounting bolt to secure the housing to the rear bracket.
38
Replace the three right-side screws.
39
Rethread the two screws securing the front of the housing.
40
"Reposition the ring seal on the housing so the phillips-head screw hole aligns with the appropriate screw hole in the gear ring, then thread the screw."
41
"Realign the handle on the chute, then reposition the assembly on the ring seal and thread the three mounting bolts to secure."
42
Refill the fuel tank.
43
Congrats! Your snowblower is ready for use.
Description
This video provides step-by-step repair instructions for replacing the fuel hose on a Toro snowblower.

All of the information for this video is applicable to the following brands:
Toro
Step-By-Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Fuel Hose Replacement
3
Tools Needed
4
"You will need a 3/8th inch socket, a phillips-head screwdriver, an 8mm socket, a half-inch socket and a 10mm socket for this procedure."
5
Make sure the engine has cooled.
6
Be sure to perform this procedure with no fuel in the tank.
7
Use a 3/8th inch socket to unthread the three mounting bolts securing the chute handle and the chute itself.
8
Remove the assembly and detach the handle.
9
"Using a phillips-head screwdriver, unthread the screw to release the chute ring seal."
10
Unthread the two front housing mounting screws.
11
Unthread the three screws from the right side of the housing.
12
Use a 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
13
Unthread the screws to release the two retaining clamps holding the housing to the handle.
14
You can now fully remove the housing.
15
Use an 8mm socket to unthread the six bolts securing the muffler cover.
16
Use a half-inch socket to fully unthread the upper bolts securing the handle assembly.
17
Lower the handle to fully remove the muffler cover.
18
Detach the primer hose from the carburetor – be prepared for some fuel to spill.
19
Disconnect the wires from the key switch terminals.
20
Use a 10mm socket to unthread the nuts securing the control housing.
21
Pull the housing off of the mounting bolts.
22
"Use a 10mm socket to unthread the two nuts and an 8mm socket to unthread the screw securing the side access cover, then pull the cover off."
23
Use the 8mm socket to unthread the two mounting screws securing the trim and fuel tank.
24
Unthread the additional screw on the left securing the tank.
25
Release the clamp to detach the fuel hose and you can fully remove the tank.
26
Release the retaining clamp to detach the old fuel hose from the carburetor and remove both clamps.
27
Install the new fuel hose by feeding it under the speed control assembly.
28
Slide the two clamps over the appropriate ends.
29
"Attach the hose to the carburetor and secure it with the clamp, then attach the opposite end to the fuel tank and secure with the clamp."
30
Reposition the tank and thread the left-side screw.
31
Realign the trim and thread the screws; realign the side access cover and thread the screw and nuts to secure.
32
"Reposition the control housing, then thread and tighten the mounting nuts."
33
Connect the wires to the key switch terminals.
34
Reattach the primer hose to the carburetor.
35
Reposition the muffler cover and thread the six bolts to secure; reposition the handle assembly and rethread the upper bolts; reposition the housing.
36
Align the two retaining clamps and thread the screws to secure the housing to the handle.
37
Rethread the mounting bolt to secure the housing to the rear bracket.
38
Replace the three right-side screws.
39
Rethread the two screws securing the front of the housing.
40
"Reposition the ring seal on the housing so the phillips-head screw hole aligns with the appropriate screw hole in the gear ring, then thread the screw."
41
"Realign the handle on the chute, then reposition the assembly on the ring seal and thread the three mounting bolts to secure."
42
Refill the fuel tank.
43
Congrats! Your snowblower is ready for use.

Applicable Product Model

Snowblower
Brand
Product Type
Model
Subtype
Product Diagram & Manuals
Parts Needed
Fuel Line
Fuel Line
$16.28
Total$0.00

Related Articles & Videos

04:12
9.9k
46
Part Replacement
Toro Snowblower Clutch Cable Replacement 140-1000
05:33
6.8k
8
Part Replacement
Toro Snowblower Carburetor Replacement 127-9111
04:07
3.2k
9
Part Replacement
Toro Snowblower Recoil Starter Replacement 127-9402
02:25
2.7k
7
Part Replacement
Toro Snowblower Scraper Blade Replacement 139-3536