Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Frigidaire Gas Range Spark Switch Wire Harness Replacement (5304510486)

06:11
1.7k
14
This video provides step-by-step instructions for replacing the spark switch wire harness on Frigidaire gas ranges.

All of the information in this video is applicable to the following brands: Frigidaire

Tools used: 3/16th-inch socket or nut driver, quarter-inch socket or nut driver & Phillips-head screwdriver, & a half-inch wrench.

Step By Step Instructions

1
Frigidaire Gas Range - Model FFGF3052TSA
2
Gas Range Spark Switch Harness Replacement
3
Tools & Assistance Needed
4
"You will need a 3/16th-inch socket or nut driver, a quarter-inch socket, string or wire and a phillips-head screwdriver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord or shut off the power supply.
6
Shut off the gas supply as well.
7
Lift off the three grates.
8
Remove all of the burner caps and lift the center burner base straight up to remove.
9
"Using a 3/16th-inch socket or nut driver, unthread the mounting screws securing the front and rear burner bases."
10
"With the screws unthreaded, lift each base straight up to remove."
11
Use a quarter-inch socket or nut driver to unthread all of the screws securing the orifice holders to the main top.
12
Pull off the control knobs – you can use string or wire to help pry them off.
13
"Open the oven door and use a phillips-head screwdriver to unthread the two mounting screws securing the valve control panel, then remove the panel."
14
Unthread the two screws securing the main top.
15
Pull the main top forward and lift up to remove.
16
Disconnect the red spark switch wire from the spark module.
17
Reach behind the rear brace and lift up the black spark switch wire to disconnect it.
18
Release the ties securing the switch wires to the manifold.
19
Detach the five spark switches from the burner valves to remove the old harness.
20
Install the new spark switch harness by snapping each switch onto the appropriate burner valve.
21
Use the ties to secure the wires to the manifold.
22
Feed the black wire through the hole in the brace and connect it.
23
Connect the red wire to the spark module.
24
Reinstall the main top by aligning the rear edge under the retaining tabs.
25
Confirm that the orifice holders and igniters protrude through the holes in the top.
26
Thread the two screws to secure.
27
"Reinstall the valve control panel by aligning the slots at the top with the bracket tabs, then thread the mounting screws."
28
Replace the control knobs.
29
Thread all of the screws to secure the orifice holders to the main top.
30
Reposition the burner bases on the main top so the igniter aligns with the notch in the base.
31
Thread the mounting screws to secure the front and rear bases.
32
"Realign all the burner caps, then reinstall the grates."
33
"Turn the gas supply back on, then plug the power cord back in or restore the power supply."
34
Congrats! Your gas range is ready for use.
Description
This video provides step-by-step instructions for replacing the spark switch wire harness on Frigidaire gas ranges.

All of the information in this video is applicable to the following brands: Frigidaire

Tools used: 3/16th-inch socket or nut driver, quarter-inch socket or nut driver & Phillips-head screwdriver, & a half-inch wrench.
Step-By-Step Instructions
1
Frigidaire Gas Range - Model FFGF3052TSA
2
Gas Range Spark Switch Harness Replacement
3
Tools & Assistance Needed
4
"You will need a 3/16th-inch socket or nut driver, a quarter-inch socket, string or wire and a phillips-head screwdriver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord or shut off the power supply.
6
Shut off the gas supply as well.
7
Lift off the three grates.
8
Remove all of the burner caps and lift the center burner base straight up to remove.
9
"Using a 3/16th-inch socket or nut driver, unthread the mounting screws securing the front and rear burner bases."
10
"With the screws unthreaded, lift each base straight up to remove."
11
Use a quarter-inch socket or nut driver to unthread all of the screws securing the orifice holders to the main top.
12
Pull off the control knobs – you can use string or wire to help pry them off.
13
"Open the oven door and use a phillips-head screwdriver to unthread the two mounting screws securing the valve control panel, then remove the panel."
14
Unthread the two screws securing the main top.
15
Pull the main top forward and lift up to remove.
16
Disconnect the red spark switch wire from the spark module.
17
Reach behind the rear brace and lift up the black spark switch wire to disconnect it.
18
Release the ties securing the switch wires to the manifold.
19
Detach the five spark switches from the burner valves to remove the old harness.
20
Install the new spark switch harness by snapping each switch onto the appropriate burner valve.
21
Use the ties to secure the wires to the manifold.
22
Feed the black wire through the hole in the brace and connect it.
23
Connect the red wire to the spark module.
24
Reinstall the main top by aligning the rear edge under the retaining tabs.
25
Confirm that the orifice holders and igniters protrude through the holes in the top.
26
Thread the two screws to secure.
27
"Reinstall the valve control panel by aligning the slots at the top with the bracket tabs, then thread the mounting screws."
28
Replace the control knobs.
29
Thread all of the screws to secure the orifice holders to the main top.
30
Reposition the burner bases on the main top so the igniter aligns with the notch in the base.
31
Thread the mounting screws to secure the front and rear bases.
32
"Realign all the burner caps, then reinstall the grates."
33
"Turn the gas supply back on, then plug the power cord back in or restore the power supply."
34
Congrats! Your gas range is ready for use.

Applicable Product Model

Range/Stove/Oven
Model
Subtype
Gas
Product Diagram & Manuals
Parts Needed
Total$0.00

Related Articles & Videos