Electrolux Front-Load Washer Heating Element Replacement (part 137488301)

02:54
668
2
This video provides step-by-step instructions for replacing the heating element on Electrolux washing machine.

All of the information in this heating element replacement video is applicable to the following brands: Electrolux

Tools used: Phillips-head screwdriver or Number two square drive bit, 10mm socket, & a flat-head screwdriver.

Step By Step Instructions

1
Electrolux Front-Load Washer - Model EFLS627UTT
2
Front-Load Washer Heating Element Replacement
3
Tools & Assistance Needed
4
"You will need a Philips-head screwdriver, a 10mm socket, and a flat-head screwdriver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord.
6
Have an assistant help you to move the appliance away from the wall.
7
"Using a Philips-head screwdriver or a number two square drive bit, unthread the six screws securing the rear access panel."
8
The bottom screw doesn’t need to be full unthreaded.
9
Set the panel aside.
10
"Note the orientation of the heating element power wires, sensor wire and grounding wire, then disconnect them."
11
"Using a 10mm socket, unthread the mounting nut."
12
Use a flat-head screwdriver to help pry the old element free of the outer tub.
13
"Install the new heating element by inserting it into the slot in the outer tub, then push until it is fully seated."
14
Thread and tighten the mounting nut.
15
"Connect the power wires, the sensor wire, and the grounding wire."
16
Reinstall the rear access panel.
17
Move the appliance back against the wall and plug the power cord back in.
18
Congrats! Your front-load washer is ready for use.
Description
This video provides step-by-step instructions for replacing the heating element on Electrolux washing machine.

All of the information in this heating element replacement video is applicable to the following brands: Electrolux

Tools used: Phillips-head screwdriver or Number two square drive bit, 10mm socket, & a flat-head screwdriver.
Step-By-Step Instructions
1
Electrolux Front-Load Washer - Model EFLS627UTT
2
Front-Load Washer Heating Element Replacement
3
Tools & Assistance Needed
4
"You will need a Philips-head screwdriver, a 10mm socket, and a flat-head screwdriver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord.
6
Have an assistant help you to move the appliance away from the wall.
7
"Using a Philips-head screwdriver or a number two square drive bit, unthread the six screws securing the rear access panel."
8
The bottom screw doesn’t need to be full unthreaded.
9
Set the panel aside.
10
"Note the orientation of the heating element power wires, sensor wire and grounding wire, then disconnect them."
11
"Using a 10mm socket, unthread the mounting nut."
12
Use a flat-head screwdriver to help pry the old element free of the outer tub.
13
"Install the new heating element by inserting it into the slot in the outer tub, then push until it is fully seated."
14
Thread and tighten the mounting nut.
15
"Connect the power wires, the sensor wire, and the grounding wire."
16
Reinstall the rear access panel.
17
Move the appliance back against the wall and plug the power cord back in.
18
Congrats! Your front-load washer is ready for use.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$8.99
Total$0.00

Related Articles & Videos

02:46
12k
14
Part Replacement
Electrolux Washer Heating Element Replacement #137488301
07:53
25k
141
Part Replacement
Electrolux Front-Load Washer Door Boot Seal Replacement (part 5304505004)
08:08
10k
21
Part Replacement
Electrolux Front-Load Washer Sump Filter Replacement (part 5304505165)
06:59
3.7k
13
Part Replacement
Electrolux Front-Load Washer Drain Pump Assembly Replacement (part 5304514775)