Frigidaire Electric Laundry Center Dryer Drum Belt Replacement (134503600)

07:04
35k
271
This video provides step-by-step repair instructions for replacing the dryer drum belt on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the dryer drum will not spin, but the motor is humming.

This replacement video is applicable to the following brands:
Frigidaire

Don't forget to like and comment on this video and subscribe to our channel!

Step By Step Instructions

1
Laundry Center- Model FFLE3900UW1
2
Laundry Center Dryer Drum Belt Idler Arm Replacement
3
Step 1: Gather a number two square drive bit or a phillips-head screwdriver.
4
Step 2: Unplug the power cord.
5
Step 3: Have an assistant help you to move the appliance away from the wall or out of the closet.
6
Step 4: Detach the venting from the dryer to fully access the rear of the laundry center.
7
Step 5: Shut off the incoming water and remove the hot and cold water supply lines as well.
8
"Step 6: If necessary, remove the drain hose from the standpipe or laundry tub. "
9
"Step 7: Use the number two square drive bit or the phillips-head screwdriver to unthread the two screws securing the dryer access panel. "
10
Step 8: Set the panel aside.
11
Step 9: Move the idler arm to the left so you can detach the belt from the motor pulley and idler pulley.
12
Step 10: Slide the old idler arm off the mounting pin and detach the spring.
13
"Step 11: When installing the new idler arm, confirm the spring is fully attached to the frame. "
14
"Step 12: With the pulley facing outward, attach the spring to the arm then align the arm on the mounting pin."
15
Step 13: Loop the belt onto the idler pulley and motor pulley in a zig-zag formation.
16
Step 14: Rotate the drum to help align the belt.
17
Step 15: Reinstall the access panel by inserting the tabs into the slots first then rethread the screws.
18
"Step 16: If necessary, reinsert the drain hose into the standpipe or hook it onto the edge of the tub."
19
Step 17: Reattach the hot and cold water supply lines to the inlet valve ports.
20
Step 18: Reattach the venting if required and move the appliance back against the wall or into the closet.
21
Step 19: Turn the water supply back on.
22
Step 20: Plug the power cord back in.
23
Congratulations! Your laundry center should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the dryer drum belt on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the dryer drum will not spin, but the motor is humming.

This replacement video is applicable to the following brands:
Frigidaire

Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Laundry Center- Model FFLE3900UW1
2
Laundry Center Dryer Drum Belt Idler Arm Replacement
3
Step 1: Gather a number two square drive bit or a phillips-head screwdriver.
4
Step 2: Unplug the power cord.
5
Step 3: Have an assistant help you to move the appliance away from the wall or out of the closet.
6
Step 4: Detach the venting from the dryer to fully access the rear of the laundry center.
7
Step 5: Shut off the incoming water and remove the hot and cold water supply lines as well.
8
"Step 6: If necessary, remove the drain hose from the standpipe or laundry tub. "
9
"Step 7: Use the number two square drive bit or the phillips-head screwdriver to unthread the two screws securing the dryer access panel. "
10
Step 8: Set the panel aside.
11
Step 9: Move the idler arm to the left so you can detach the belt from the motor pulley and idler pulley.
12
Step 10: Slide the old idler arm off the mounting pin and detach the spring.
13
"Step 11: When installing the new idler arm, confirm the spring is fully attached to the frame. "
14
"Step 12: With the pulley facing outward, attach the spring to the arm then align the arm on the mounting pin."
15
Step 13: Loop the belt onto the idler pulley and motor pulley in a zig-zag formation.
16
Step 14: Rotate the drum to help align the belt.
17
Step 15: Reinstall the access panel by inserting the tabs into the slots first then rethread the screws.
18
"Step 16: If necessary, reinsert the drain hose into the standpipe or hook it onto the edge of the tub."
19
Step 17: Reattach the hot and cold water supply lines to the inlet valve ports.
20
Step 18: Reattach the venting if required and move the appliance back against the wall or into the closet.
21
Step 19: Turn the water supply back on.
22
Step 20: Plug the power cord back in.
23
Congratulations! Your laundry center should be ready for use.

Applicable Product Model

Washer/Dryer Combo
Model
Subtype
Product Diagram & Manuals
Parts Needed
Recommended Tools and Accessories
Total$0.00

Related Articles & Videos

10:24
33k
286
Part Replacement
Frigidaire Electric Laundry Center Heater Assembly Replacement (137392702)
09:35
19k
158
Part Replacement
Frigidaire Electric Laundry Center Dryer Drum Bearing Replacement (131777700)
18:36
19k
154
Part Replacement
Frigidaire Laundry Center Washer Transmission Assembly Replacement (5304517318)
04:37
16k
81
Part Replacement
Frigidaire Laundry Center Washer Drain Pump Replacement (5304524452)