1-800-269-2609 24/7
Orders placed by 8:00 p.m. ET Monday through Friday will ship the same day.
Dishwasher Not Draining? Drain Pump Replacement #00642239
Skill Level
Total Parts Cost
$121.70Estimated Savings
$112.5002:51
312k
385
- Description
This video provides step-by-step instructions for replacing the drain pump on Bosch dishwashers. The most common reasons to replace the drain pump are when the dishwasher is not draining, is making noise, or when its lights are flashing or blinking.
All of the information in this drain pump replacement video is applicable to the following brands: Bosch, Thermador, Gaggenau, Kenmore.
All of the information in this drain pump replacement video is applicable to the following brands: Bosch, Thermador, Gaggenau, Kenmore.
Step By Step Instructions
1
As with any repair, be sure to turn off the power to your dishwasher before beginning.
2
Next, remove the screws to release the lower access panel and set the panel aside.
3
Now open the dishwasher door and remove the screws securing the outer door panel.
4
Close the door securely and pull the outer door panel down to remove.
5
Uninstall the screws to release the inner access plate.
6
Detach the plate from the harness support and set it aside.
7
Move the sound dampening pad out of the way.
8
Release the fill hose from the retaining clip and pull it off of the sump and air pressure chamber.
9
Be prepared for some water to spill out.
10
Disconnect the wire harness from the drain pump.
11
Now release the locking tab on the pump and rotate the old pump clockwise to remove it.
12
Install the new drain pump by aligning it with the tabs in the sump.
13
Push and rotate the pump counter-clockwise to lock it into place.
14
Connect the wire harness to the new pump
15
Replace the fill hose by inserting it into the port on the pressure chamber and the port on the sump.
16
Secure it in the retaining clip.
17
Reposition the sound dampening pad.
18
Replace the inner access plate by hooking it on to the frame and harness support then secure it with the screws.
19
Reinstall the outer door panel by sliding it up into position and replace the screws in the inner panel to secure.
20
Replace the lower access panel and secure the screws.
21
You’re now ready to turn the power supply back on and confirm that the dishwasher is functioning properly.
Description
This video provides step-by-step instructions for replacing the drain pump on Bosch dishwashers. The most common reasons to replace the drain pump are when the dishwasher is not draining, is making noise, or when its lights are flashing or blinking.
All of the information in this drain pump replacement video is applicable to the following brands: Bosch, Thermador, Gaggenau, Kenmore.
All of the information in this drain pump replacement video is applicable to the following brands: Bosch, Thermador, Gaggenau, Kenmore.
Step-By-Step Instructions
1
As with any repair, be sure to turn off the power to your dishwasher before beginning.
2
Next, remove the screws to release the lower access panel and set the panel aside.
3
Now open the dishwasher door and remove the screws securing the outer door panel.
4
Close the door securely and pull the outer door panel down to remove.
5
Uninstall the screws to release the inner access plate.
6
Detach the plate from the harness support and set it aside.
7
Move the sound dampening pad out of the way.
8
Release the fill hose from the retaining clip and pull it off of the sump and air pressure chamber.
9
Be prepared for some water to spill out.
10
Disconnect the wire harness from the drain pump.
11
Now release the locking tab on the pump and rotate the old pump clockwise to remove it.
12
Install the new drain pump by aligning it with the tabs in the sump.
13
Push and rotate the pump counter-clockwise to lock it into place.
14
Connect the wire harness to the new pump
15
Replace the fill hose by inserting it into the port on the pressure chamber and the port on the sump.
16
Secure it in the retaining clip.
17
Reposition the sound dampening pad.
18
Replace the inner access plate by hooking it on to the frame and harness support then secure it with the screws.
19
Reinstall the outer door panel by sliding it up into position and replace the screws in the inner panel to secure.
20
Replace the lower access panel and secure the screws.
21
You’re now ready to turn the power supply back on and confirm that the dishwasher is functioning properly.
Applicable Product Model
Parts Needed
Drain Pump
$121.70
Total$0.00
Related Articles & Videos
03:10
347k
578
Part Replacement
Bosch Dishwasher Won't Fill? Replace Water Inlet Valve #622058
About Us
Start doing it yourself with the confidence that comes with 100+ years of experience. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right.
© 2023 RepairClinic.com1‑800‑269‑2609
