Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

Whirlpool/Kenmore Electric Dryer Right Door Hinge #8066056

03:15
5.9k
12
This video provides step-by-step repair instructions for replacing the right door hinge on a Whirlpool/Kenmore electric dryer. The most common reason for replacing the door hinge is when the dryer door doesn't open smoothly.

All of the information for this right door hinge replacement video is applicable to the following brands:
Kenmore, Whirlpool, KitchenAid, Crosley, Roper, Estate, Maytag, Admiral, Amana

Tools needed: hex socket, flat head screwdriver, Phillips head screwdriver, putty knife

Step By Step Instructions

1
As with any repair, be sure you’ve unplugged the appliance before beginning.
2
Your first step is to pull out the lint screen and remove the two screws near the opening.
3
Next, insert a putty knife under the front of the main top to release the two spring clips and rotate the top up.
4
Disconnect the door switch wires and remove the top front panel screws.
5
Now, lift the panel up and out.
6
If your model has two front panels
7
Use a flathead screwdriver to release the clips above the lower panel to remove it.
8
Now, loosen the two screws at the bottom of the upper panel and lift the panel off.
9
If applicable to your model, remove both door springs.
10
Next, uninstall the screws that hold the door to the hinge, and set the door aside.
11
Remove the hinge mounting screws from the front panel and pull out the old door hinge.
12
Install the new door hinge by inserting it into the front panel and securing it with the screws.
13
Reinstall the door and reconnect the door springs if applicable.
14
You’re now ready to reinstall the front panel or panels.
15
If your model has a solid front panel, align the slots in the panel with the two retainer clips.
16
Line up the drum with the seal on the front panel and press the panel down until it locks into position.
17
If your model has two panels, align the slots in the upper panel with the screws while lining up the drum.
18
Tighten the screws and replace the lower panel by snapping it into position.
19
Now, reinstall the two screws on top and reconnect the door switch wires.
20
Rotate the main top back into place and press down on the front to secure the spring clips.
21
Install the two screws at the lint screen opening replace the lint screen and plug the appliance back in.
Description
This video provides step-by-step repair instructions for replacing the right door hinge on a Whirlpool/Kenmore electric dryer. The most common reason for replacing the door hinge is when the dryer door doesn't open smoothly.

All of the information for this right door hinge replacement video is applicable to the following brands:
Kenmore, Whirlpool, KitchenAid, Crosley, Roper, Estate, Maytag, Admiral, Amana

Tools needed: hex socket, flat head screwdriver, Phillips head screwdriver, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you’ve unplugged the appliance before beginning.
2
Your first step is to pull out the lint screen and remove the two screws near the opening.
3
Next, insert a putty knife under the front of the main top to release the two spring clips and rotate the top up.
4
Disconnect the door switch wires and remove the top front panel screws.
5
Now, lift the panel up and out.
6
If your model has two front panels
7
Use a flathead screwdriver to release the clips above the lower panel to remove it.
8
Now, loosen the two screws at the bottom of the upper panel and lift the panel off.
9
If applicable to your model, remove both door springs.
10
Next, uninstall the screws that hold the door to the hinge, and set the door aside.
11
Remove the hinge mounting screws from the front panel and pull out the old door hinge.
12
Install the new door hinge by inserting it into the front panel and securing it with the screws.
13
Reinstall the door and reconnect the door springs if applicable.
14
You’re now ready to reinstall the front panel or panels.
15
If your model has a solid front panel, align the slots in the panel with the two retainer clips.
16
Line up the drum with the seal on the front panel and press the panel down until it locks into position.
17
If your model has two panels, align the slots in the upper panel with the screws while lining up the drum.
18
Tighten the screws and replace the lower panel by snapping it into position.
19
Now, reinstall the two screws on top and reconnect the door switch wires.
20
Rotate the main top back into place and press down on the front to secure the spring clips.
21
Install the two screws at the lint screen opening replace the lint screen and plug the appliance back in.

Applicable Product Model

Parts Needed
Recommended Tools and Accessories
Total$0.00

Related Articles & Videos