Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more
Whirlpool Top Load Washer Water Inlet Assembly #W10432353
Skill Level
Total Parts Cost
$130.55Estimated Savings
$112.5002:17
10k
13
- Description
This video provides step-by-step repair instructions for replacing the water inlet valve assembly on a Whirlpool top-loading washing machine. The most common reasons for replacing the water inlet valve assembly are when the washer fills slowly, overflows, or stops mid-cycle.
All of the information for this water inlet valve assembly replacement video is applicable to the following brands:
Kenmore, Whirlpool, Maytag, Crosley, Amana
All of the information for this water inlet valve assembly replacement video is applicable to the following brands:
Kenmore, Whirlpool, Maytag, Crosley, Amana
Step By Step Instructions
1
As with any repair, you should unplug the appliance before beginning
2
Turn off the hot and cold water supply valves.
3
Your first step is to disconnect the water supply hoses from the inlet valve. Be prepared for some water to spill out.
4
Next, insert a putty knife under the control panel to release the two spring clips. then rotate the panel forward.
5
Now detach the inlet valve wire connector from the control board.
6
Remove the screws securing the inlet valve mounting bracket to the main top and the screws securing the inlet valve water spout.
7
You can now remove the old water inlet assembly.
8
Install the new water inlet assembly by first inserting the spout into the main top and aligning the mounting bracket.
9
Secure all of the screws.
10
Attach the new wire connector to the control board.
11
Align the control panel on the top edge of the upper access panel.
12
Now insert the rear tabs of the control panel into the slots in the main top and snap the panel into position.
13
Connect the water supply hoses to the new inlet valve and turn the water supply back on.
14
You’re now ready to plug the power cord back in and confirm that the washer is functioning properly.
Description
This video provides step-by-step repair instructions for replacing the water inlet valve assembly on a Whirlpool top-loading washing machine. The most common reasons for replacing the water inlet valve assembly are when the washer fills slowly, overflows, or stops mid-cycle.
All of the information for this water inlet valve assembly replacement video is applicable to the following brands:
Kenmore, Whirlpool, Maytag, Crosley, Amana
All of the information for this water inlet valve assembly replacement video is applicable to the following brands:
Kenmore, Whirlpool, Maytag, Crosley, Amana
Step-By-Step Instructions
1
As with any repair, you should unplug the appliance before beginning
2
Turn off the hot and cold water supply valves.
3
Your first step is to disconnect the water supply hoses from the inlet valve. Be prepared for some water to spill out.
4
Next, insert a putty knife under the control panel to release the two spring clips. then rotate the panel forward.
5
Now detach the inlet valve wire connector from the control board.
6
Remove the screws securing the inlet valve mounting bracket to the main top and the screws securing the inlet valve water spout.
7
You can now remove the old water inlet assembly.
8
Install the new water inlet assembly by first inserting the spout into the main top and aligning the mounting bracket.
9
Secure all of the screws.
10
Attach the new wire connector to the control board.
11
Align the control panel on the top edge of the upper access panel.
12
Now insert the rear tabs of the control panel into the slots in the main top and snap the panel into position.
13
Connect the water supply hoses to the new inlet valve and turn the water supply back on.
14
You’re now ready to plug the power cord back in and confirm that the washer is functioning properly.
Applicable Product Model
Parts Needed
Water Inlet Valve
$130.55
Recommended Tools and Accessories
Fill Hose
$46.32
Cleaner
$8.99
Cleaner
$20.66
Cleaner
$14.18
Cleaner
$22.37
Cooktop Cleaner
$16.06
Total$0.00
About Us
Start doing it yourself with the confidence that comes with 100+ years of experience. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right.
© 2022 RepairClinic.com1‑800‑269‑2609
