Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

LG Dishwasher Leveling Leg Replacement #AGM72461901

04:48
15k
11
This video provides step-by-step instructions for replacing a leveling leg on LG dishwashers. The most common reason for replacing a leveling leg is when it is worn, broken, or lost, causing the dishwasher to lean forward and leak water.

All of the information in this leveling leg replacement video is applicable to the following brands: LG

Step By Step Instructions

1
To replace a front leveling leg, you will need to uninstall the dishwasher first.
2
To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panel.
5
Pull out the sound dampening pad.
6
Disconnect the water supply line from the inlet valve.
7
Be prepared for some water to spill out.
8
Remove the screw to release the junction box cover.
9
Note the location of the wires then untwist the wire nuts to disconnect the wires.
10
Use a flathead screwdriver to help remove the strain relief nut and detach the strain relief from the junction box.
11
Next, disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the legs to lower the appliance.
14
You can adjust the rear leveling legs by turning the shaft assembly screws at the front.
15
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
16
Now tip the dishwasher back and use a wood block or comparable sturdy object to support it.
17
Use a small flathead screwdriver to depress the tabs to release the old leveling leg.
18
Install the new leveling leg by aligning it with the base and snapping it into place.
19
Remove the support and gently lower the dishwasher to the floor.
20
Make sure the end of the drain hose is accessible through the cabinet wall.
21
Lift the right side of the dishwasher up and support it.
22
Guide the electrical supply line under the appliance so its wires are accessible through the hole in the junction box.
23
Now remove the support and gently slide the dishwasher back into the cabinet.
24
Adjust the leveling legs if necessary.
25
Replace the screws to secure the mounting brackets to the cabinet or countertop.
26
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
27
Make sure the hose is elevated above the connection point.
28
Fully position the wire strain relief in the junction box and secure the strain relief nut.
29
Connect the wires using the wire nuts.
30
Align the cover plate and replace the screw to secure.
31
Reconnect the water supply line to the inlet valve.
32
Replace the sound dampening pad.
33
Replace the lower access panel and secure it with the screws.
34
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.
Description
This video provides step-by-step instructions for replacing a leveling leg on LG dishwashers. The most common reason for replacing a leveling leg is when it is worn, broken, or lost, causing the dishwasher to lean forward and leak water.

All of the information in this leveling leg replacement video is applicable to the following brands: LG
Step-By-Step Instructions
1
To replace a front leveling leg, you will need to uninstall the dishwasher first.
2
To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panel.
5
Pull out the sound dampening pad.
6
Disconnect the water supply line from the inlet valve.
7
Be prepared for some water to spill out.
8
Remove the screw to release the junction box cover.
9
Note the location of the wires then untwist the wire nuts to disconnect the wires.
10
Use a flathead screwdriver to help remove the strain relief nut and detach the strain relief from the junction box.
11
Next, disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the legs to lower the appliance.
14
You can adjust the rear leveling legs by turning the shaft assembly screws at the front.
15
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
16
Now tip the dishwasher back and use a wood block or comparable sturdy object to support it.
17
Use a small flathead screwdriver to depress the tabs to release the old leveling leg.
18
Install the new leveling leg by aligning it with the base and snapping it into place.
19
Remove the support and gently lower the dishwasher to the floor.
20
Make sure the end of the drain hose is accessible through the cabinet wall.
21
Lift the right side of the dishwasher up and support it.
22
Guide the electrical supply line under the appliance so its wires are accessible through the hole in the junction box.
23
Now remove the support and gently slide the dishwasher back into the cabinet.
24
Adjust the leveling legs if necessary.
25
Replace the screws to secure the mounting brackets to the cabinet or countertop.
26
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
27
Make sure the hose is elevated above the connection point.
28
Fully position the wire strain relief in the junction box and secure the strain relief nut.
29
Connect the wires using the wire nuts.
30
Align the cover plate and replace the screw to secure.
31
Reconnect the water supply line to the inlet valve.
32
Replace the sound dampening pad.
33
Replace the lower access panel and secure it with the screws.
34
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.

Applicable Product Model

Dishwasher
Brand
Product Type
Model
Subtype
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$20.66
Total$0.00

Related Articles & Videos