Shipping all 7 days! Hold times are long. Already ordered? Email [email protected]Learn more

LG Dishwasher Noise Filter Replacement #6201EC1006T

loading...

06:36
30k
45
This video provides step-by-step instructions for replacing the noise filter on LG dishwashers. The most common reason for replacing the noise filter is when electrical interference in your home’s power supply disrupt the control board or other electrical components of the dishwasher during its operation.

All of the information in this noise filter replacement video is applicable to the following brands: LG

Step By Step Instructions

1
To replace the noise filter, you will need to uninstall the dishwasher first.
2
To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panel.
5
Pull out the sound dampening pad.
6
Disconnect the water supply line from the inlet valve.
7
Be prepared for some water to spill out.
8
Remove the screw to release the junction box cover.
9
Note the location of the wires then untwist the wire nuts to disconnect the wires.
10
Use a flathead screwdriver to help remove the strain relief nut and detach the strain relief from the junction box.
11
Next, disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the legs to lower the appliance.
14
You can adjust the rear leveling legs by turning the shaft assembly screws at the front.
15
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
16
Open the door and remove both the upper and lower dish racks.
17
Close the door and use tape to secure the mounting brackets.
18
Now carefully tip the dishwasher upside-down with its top resting on a blanket or towel.
19
Remove the screws securing the bottom access plate and pull the plate free.
20
Next, disconnect the two wire connecters from the noise filter.
21
Remove the mounting screw securing the filter.
22
Use a small flathead screwdriver to depress the tab to release the old noise filter from the base.
23
Install the new noise filter by hooking the tab onto the base then snap the filter into place.
24
Replace the mounting screw.
25
Attach the wire connecters to the new filter.
26
Replace the bottom access plate and secure it with the screws.
27
You’re now ready to return the dishwasher to its upright position.
28
Remove the tape securing the mounting brackets.
29
Open the door and replace both the upper and lower dish racks.
30
You’re now ready to reinstall the dishwasher.
31
Make sure the end of the drain hose is accessible through the cabinet wall.
32
Lift the right side of the dishwasher up and support it with a wood block or a comparable sturdy object.
33
Guide the electrical supply line under the appliance so its wires are accessible through the hole in the junction box.
34
Now remove the support and gently slide the dishwasher back into the cabinet.
35
Adjust the leveling legs if necessary.
36
Replace the screws to secure the mounting brackets to the cabinet or countertop.
37
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
38
Make sure the hose is elevated above the connection point.
39
Fully position the wire strain relief in the junction box and secure the strain relief nut.
40
Connect the wires using the wire nuts.
41
Align the cover plate and replace the screw to secure.
42
Reconnect the water supply line to the inlet valve.
43
Replace the sound dampening pad.
44
Replace the lower access panel and secure it with the screws.
45
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.
Description
This video provides step-by-step instructions for replacing the noise filter on LG dishwashers. The most common reason for replacing the noise filter is when electrical interference in your home’s power supply disrupt the control board or other electrical components of the dishwasher during its operation.

All of the information in this noise filter replacement video is applicable to the following brands: LG
Step-By-Step Instructions
1
To replace the noise filter, you will need to uninstall the dishwasher first.
2
To do this, turn off the power to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panel.
5
Pull out the sound dampening pad.
6
Disconnect the water supply line from the inlet valve.
7
Be prepared for some water to spill out.
8
Remove the screw to release the junction box cover.
9
Note the location of the wires then untwist the wire nuts to disconnect the wires.
10
Use a flathead screwdriver to help remove the strain relief nut and detach the strain relief from the junction box.
11
Next, disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the legs to lower the appliance.
14
You can adjust the rear leveling legs by turning the shaft assembly screws at the front.
15
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
16
Open the door and remove both the upper and lower dish racks.
17
Close the door and use tape to secure the mounting brackets.
18
Now carefully tip the dishwasher upside-down with its top resting on a blanket or towel.
19
Remove the screws securing the bottom access plate and pull the plate free.
20
Next, disconnect the two wire connecters from the noise filter.
21
Remove the mounting screw securing the filter.
22
Use a small flathead screwdriver to depress the tab to release the old noise filter from the base.
23
Install the new noise filter by hooking the tab onto the base then snap the filter into place.
24
Replace the mounting screw.
25
Attach the wire connecters to the new filter.
26
Replace the bottom access plate and secure it with the screws.
27
You’re now ready to return the dishwasher to its upright position.
28
Remove the tape securing the mounting brackets.
29
Open the door and replace both the upper and lower dish racks.
30
You’re now ready to reinstall the dishwasher.
31
Make sure the end of the drain hose is accessible through the cabinet wall.
32
Lift the right side of the dishwasher up and support it with a wood block or a comparable sturdy object.
33
Guide the electrical supply line under the appliance so its wires are accessible through the hole in the junction box.
34
Now remove the support and gently slide the dishwasher back into the cabinet.
35
Adjust the leveling legs if necessary.
36
Replace the screws to secure the mounting brackets to the cabinet or countertop.
37
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
38
Make sure the hose is elevated above the connection point.
39
Fully position the wire strain relief in the junction box and secure the strain relief nut.
40
Connect the wires using the wire nuts.
41
Align the cover plate and replace the screw to secure.
42
Reconnect the water supply line to the inlet valve.
43
Replace the sound dampening pad.
44
Replace the lower access panel and secure it with the screws.
45
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.

Applicable Product Model

Dishwasher
Brand
Product Type
Model
Subtype
Parts Needed
Recommended Tools and Accessories
Cleaner
Cleaner
$8.99
Cleaner
Cleaner
$24.85
Cleaner
Cleaner
$10.58
Cleaner
Cleaner
$22.11
Total$0.00

Related Articles & Videos