• 1-800-269-2609
  • En Español
  • Available 7 days a week

Kenmore Dryer Drum Not Turning

110.66722690

The part(s) or condition(s) listed below for the symptom Dryer drum not turning are ordered from most likely to least likely to occur. Check or test each item, starting with the items at the top of the page.

Most Frequent Causes for Dryer drum not turning

Cause 1Drive Belt

The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it.

Parts
Drive Belt for your KenmoreDryer
Drive Belt - Part # 529597 Mfg Part # 341241

Dryer drum drive belt. The belt is flat, 92-1/4 inches long, 1/4 inch wide and has 4 ribs and 3 grooves. It replaces many other belts, including some with 5 ribs and 4 grooves. If the drum does not turn, but you can hear the motor running then there is a good chance the belt has broken.

Add to Cart
Install Help
Cause 2Drum Roller

Most dryers have two drum rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If one or more of the rollers are worn out, we recommend replacing all of the rollers at the same time as a preventative measure. (The roller shaft can often be reused if it is in good condition. Clean the shaft thoroughly before installing the new rollers.)

Parts
Drum Roller for your KenmoreDryer
Drum Roller - Part # 3436 Mfg Part # 349241T

Rear drum support roller kit. This kit contains two drum support rollers. If the drum rollers are worn out, the dryer may not turn properly or may be excessively noisy. Be aware that the drum bearings are self-lubricating; it is not necessary to lubricate them yourself.

Add to Cart
Install Help
Cause 3Drum Roller Axle

Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. Over time, the drum roller axles can wear out, causing the rollers to bind. If the rollers are worn out or start binding, the motor will get overloaded and the dryer won’t turn. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, they do not need to be replaced. If a roller wobbles and/or does not spin freely, we recommend replacing all of the axles and rollers as a preventative measure.

Parts
Drum Roller Axle for your KenmoreDryer
Drum Roller Axle - Part # 1878660 Mfg Part # WPW10359269

Shaft for drum support roller, right side

Add to Cart
Install Help
Cause 4Drum Roller Axle

Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. Over time, the drum roller axles can wear out, causing the rollers to bind. If the rollers are worn out or start binding, the motor will get overloaded and the dryer won’t turn. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, they do not need to be replaced. If a roller wobbles and/or does not spin freely, we recommend replacing all of the axles and rollers as a preventative measure.

Parts
Drum Roller Axle for your KenmoreDryer
Drum Roller Axle - Part # 1878661 Mfg Part # WPW10359270

Shaft for drum support roller, left side

Add to Cart
Install Help
Cause 5Drum Slide, Glide, or Pad

One or more of the drum glides (also called slides) might be worn out. The drum glides are small plastic pieces that support the front of the dryer drum. As the drum rotates, it slides on these plastic pieces. Over time, the drum glides wear out. If the drum glides are worn out, the drum can start binding and put strain on the motor. If this happens, the motor shuts down, preventing the dryer from turning. To determine if the drum glides are worn out, inspect them for wear. If one or more of the glides are worn out, replace all of the glides as a set.

Parts
Drum Slide, Glide, or Pad for your KenmoreDryer
Drum Slide, Glide, or Pad - Part # 2683 Mfg Part # 279441

Ring bearing kit, front of dryer drum

Add to Cart
Install Help
Cause 6Drive Motor

The drive motor turns the drum and the blower wheel to exhaust the air. First, check the motor to see if it makes a humming noise. If the motor still hums, remove the belt from the motor and check the blower wheel to ensure that it is not obstructed. Next, with the belt removed, try rotating the drum by hand. If the drum does not rotate freely, determine what is causing the drum to bind. If the drum turns freely and the blower wheel is clear of obstructions, the drive motor might be defective. If you suspect the motor is at fault, replace it.

Parts
Drive Motor for your KenmoreDryer
Drive Motor - Part # 2584 Mfg Part # 279827

Dryer drum drive motor. Includes pulley for dryer drum drive belt. Other shaft has reverse threads for blower wheel. Common symptoms of a bad drive motor are:
-Dryer stops turning during cycle
-Dryer won't start
-Dryer won't turn at all
-Dryer drive motor is loud

Add to Cart
Install Help