• 1-800-269-2609
  • En Español
  • Available 7 days a week

Kenmore Dryer Won't Stop

110.66722690

The part(s) or condition(s) listed below for the symptom Dryer won't stop are ordered from most likely to least likely to occur. Check or test each item, starting with the items at the top of the page.

Most Frequent Causes for Dryer won't stop

Cause 1Air Flow Problem

If the vent is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time. To ensure proper dryer performance, you should clean your dryer’s venting system at least once per year.

Cause 2Blower Wheel

The blower wheel draws air through the dryer and pushes the air out the vent. Clumps of lint, socks, and small articles of clothing can escape the lint filter and get caught in the blower wheel. In addition, the blower wheel sleeve can wear out, allowing the blower wheel to wobble on the motor shaft. If the blower wheel is obstructed or defective, it may take too long to dry clothes. To determine if the blower wheel is working properly, remove the dryer vent and assess the strength of the air flow. If the air flow is weak, check the blower wheel for obstructions. If no obstructions are present, try rotating the blower wheel by hand. If the blower wheel wobbles as it turns, replace it.

Parts
Blower Wheel for your KenmoreDryer
Blower Wheel - Part # 686172 Mfg Part # WP694089

Dryer blower wheel. Used on 29 inch Whirlpool built models with lint filter on top. To remove the blower wheel, unscrew the blower wheel clockwise off the motor shaft.

Add to Cart
Install Help
Cause 3Heating Element

The heating element warms the air before the air enters the dryer drum. Over time, the heating element can burn out. If the heating element isn’t working, the clothes will take substantially longer to dry. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it.

Part Testing
Parts
Heating Element for your KenmoreDryer
Heating Element - Part # 2438 Mfg Part # 279838

Dryer heating element. If your dryer does not heat first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases the heating element will have a break in the element if defective.

Add to Cart
Install Help
Cause 4Lint Filter

The lint filter might be clogged. Dryer sheets and fabric softener can leave a residue on the lint filter, reducing the air flow. If the lint filter is clogged, clean it.

Parts
Lint Filter for your KenmoreDryer
Lint Filter - Part # 3379136 Mfg Part # WPW10717210

Dryer lint screen assembly. Proper air flow is critical to dryer operation so the filter should be cleaned before every load.

Add to Cart
Cause 5Cycling Thermostat

The cycling thermostat cycles the heat on and off to regulate the air temperature. If the cycling thermostat is defective, the dryer will not heat. However, this is rarely the case. Before replacing the cycling thermostat check all the more commonly defective parts. If you have determined that all of the other components are working properly, test the thermostat by using a multimeter to test for continuity. If the thermostat does not have continuity, replace it.

Part Testing
Parts
Cycling Thermostat for your KenmoreDryer
Cycling Thermostat - Part # 2893 Mfg Part # WP3387134

Dryer cycling thermostat with internal bias heater, L155-25. If the dryer won't heat, it is unlikely that this thermostat is causing the issue, as the thermal fuse or thermal cut-out normally fail first.

Add to Cart
Install Help
Cause 6High Limit Thermostat

The high-limit thermostat monitors the dryer temperature and shuts off the burner if the dryer overheats. If the high-limit thermostat is malfunctioning, it may shut off the burner even if the dryer is not overheating. However, this is rarely the case. Before replacing the high limit thermostat check all the more commonly defective parts. If you have determined that all of the other components are working properly, test the thermostat by using a multimeter to test it for continuity. If the thermostat does not have continuity, replace it..

Part Testing
Parts
High Limit Thermostat for your KenmoreDryer
High Limit Thermostat - Part # 2924 Mfg Part # WP3390291

High-limit thermostat, 2 wire, 250 degree limit, 60 degree cool down before reset. The high-limit thermostat cuts off power to the dryer if it overheats. If the thermostat has tripped, the dryer will not heat. To determine if the thermostat is defective, use a multimeter to test it for continuity.

Add to Cart
Cause 7Timer

Mechanical timers have a motor on them like a clock that rotates the timer down to the off position on the control panel. If the motor goes bad on the timer it will not move when set to a timed dry cycle and the dryer won’t stop.

Parts
Timer for your KenmoreDryer
Timer - Part # 548376 Mfg Part # WP3976577
Add to Cart