• 1-800-269-2609
  • En Español
  • Available 7 days a week

Maytag Dryer Not Heating

PYG2300AWW

The part(s) or condition(s) listed below for the symptom Dryer not heating are ordered from most likely to least likely to occur. Check or test each item, starting with the items at the top of the page.

Most Frequent Causes for Dryer not heating

Cause 1Thermal Fuse

The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.

Part Testing
Parts
Thermal Fuse for your MaytagDryer
Thermal Fuse - Part # 3344 Mfg Part # LA-1053

Dryer thermal fuse and high limit thermostat kit for both gas and electric models. If the dryer does not heat then the thermal fuse may have blown and will need to be replaced.

Add to Cart
Cause 2Gas Valve Solenoid

Gas dryers have two or more gas valve solenoid coils. The gas valve solenoids open the gas valve ports to allow gas to flow into the burner assembly. If a gas valve solenoid fails, the dryer won’t heat. To determine if one or more of the gas valve solenoids has failed, check the igniter. If the igniter glows and goes out but does not ignite the gas, the gas valve solenoid is defective. If one or more of the gas valve coils are defective, we recommend that you replace them as a set.

Part Testing
Parts
Gas Valve Solenoid for your MaytagDryer
Gas Valve Solenoid - Part # 3479 Mfg Part # 279834

Dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective. To test, watch the burner and if the igniter glows for a while and then shuts off without the gas igniting, it usually means one of these coils is bad.

Add to Cart
Install Help
Cause 3Igniter

The igniter uses heat to ignite the gas in the burner assembly. If the igniter is not working, the gas will not ignite, preventing the dryer from heating. To determine if the igniter has burned out, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it.

Part Testing
Parts
Igniter for your MaytagDryer
Igniter - Part # 1033270 Mfg Part # WP31001556

Glow bar igniter with wire harness

Add to Cart
Cause 4Flame Sensor

On a gas dryer, the flame sensor detects the heat emitted by the flame. If the flame sensor isn’t working, the dryer won’t heat. Before checking the flame sensor, first make sure that the igniter and thermal fuse are not at fault. To determine if the flame sensor is defective, use a multimeter to test the sensor for continuity at room temperature. If the flame sensor does not have continuity at room temperature, replace it.

Part Testing
Parts
Flame Sensor for your MaytagDryer
Flame Sensor - Part # 2681 Mfg Part # WP338906

Gas dryer sensor for igniter and flame. The sensor is located across from the gas igniter at the dryer’s burner assembly. This flame sensor should be closed for continuity at room temperature. Check for continuity with a multi-meter before replacing.

Add to Cart
Install Help
Cause 5Incoming Power Problem

If your dryer is not heating, then you may have an incoming power problem. Electric dryers need two legs of 120 volts AC equaling 240 volts. It is not uncommon for only one fuse or breaker to trip resulting in the dryer able to run, but not heat. The fuse box or circuit breaker should be checked or voltage measured at the outlet using a multi-meter.

Cause 6Cycling Thermostat

The cycling thermostat cycles the heat on and off to regulate the air temperature. If the cycling thermostat is defective, the dryer will not heat. However, this is rarely the case. Before replacing the cycling thermostat check all the more commonly defective parts. If you have determined that all of the other components are working properly, test the thermostat by using a multimeter to test for continuity. If the thermostat does not have continuity, replace it.

Part Testing
Parts
Cycling Thermostat for your MaytagDryer
Cycling Thermostat - Part # 487628 Mfg Part # WP31001088

Control thermostat, L146-25F, 120 Volt internal heater

Add to Cart
Cause 7Cycling Thermostat

The cycling thermostat cycles the heat on and off to regulate the air temperature. If the cycling thermostat is defective, the dryer will not heat. However, this is rarely the case. Before replacing the cycling thermostat check all the more commonly defective parts. If you have determined that all of the other components are working properly, test the thermostat by using a multimeter to test for continuity. If the thermostat does not have continuity, replace it.

Part Testing
Parts
Cycling Thermostat for your MaytagDryer
Cycling Thermostat - Part # 487706 Mfg Part # WP31001192

Control thermostat, L146-25F, 240 Volt internal heater

Add to Cart
Cause 8Timer

If the dryer doesn’t heat, the timer might be defective. However, this is very rarely the case. Before replacing the timer, check all the more commonly defective parts. If you determine that all of the other components are working properly, test the timer by using a multimeter and consulting the wiring diagram. If the timer is defective, replace it.

Parts
Timer for your MaytagDryer
Timer - Part # 607241 Mfg Part # WP53-1810

Timer. NOTE: Timers are often misdiagnosed. Visit our Repair Help section of the website for additional repair information.

Add to Cart