• 1-800-269-2609
  • En Español
  • Available 7 days a week

Kenmore Dryer Not Heating

110.84832201

The part(s) or condition(s) listed below for the symptom Dryer not heating are ordered from most likely to least likely to occur. Check or test each item, starting with the items at the top of the page.

Most Frequent Causes for Dryer not heating

Cause 1Thermal Fuse

The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.

Part Testing
Parts
Thermal Fuse for your KenmoreDryer
Thermal Fuse - Part # 2986 Mfg Part # WP3392519

Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won't start or will run but not heat. The thermal fuse cannot be reset. Fuses often blow due to a clogged dryer vent.

Add to Cart
Install Help
Cause 2Thermal Fuse

The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.

Part Testing
Parts
Thermal Fuse for your KenmoreDryer
Thermal Fuse - Part # 897710 Mfg Part # 279973

Dryer high limit thermostat and thermal fuse kit. If the dryer does not heat the most common cause is a blown thermal fuse. Both the thermostat and fuse can be tested to determine if either is defective.

Add to Cart
Install Help
Cause 3Heating Element

The heating element warms the air before it enters the dryer drum. Over time, the heating element can burn out, causing the dryer not to heat. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it.

Part Testing
Parts
Heating Element for your KenmoreDryer
Heating Element - Part # 525502 Mfg Part # WP3387747

Dryer heating element assembly. If the dryer does not heat the thermal fuse should be checked before replacing the heating element. Normally, the element will have a break in the coil if defective.

Add to Cart
Cause 4Incoming Power Problem

If your dryer is not heating, then you may have an incoming power problem. Electric dryers need two legs of 120 volts AC equaling 240 volts. It is not uncommon for only one fuse or breaker to trip resulting in the dryer able to run, but not heat. The fuse box or circuit breaker should be checked or voltage measured at the outlet using a multi-meter.

Cause 5High Limit Thermostat

The high-limit thermostat monitors the dryer temperature and shuts off the burner if the dryer overheats. If the high-limit thermostat is malfunctioning, it may shut off the burner even if the dryer is not overheating. However, this is rarely the case. Before replacing the high limit thermostat check all the more commonly defective parts. If you have determined that all of the other components are working properly, test the thermostat by using a multimeter to test it for continuity. If the thermostat does not have continuity, replace it.

Part Testing
Parts
High Limit Thermostat for your KenmoreDryer
High Limit Thermostat - Part # 526282 Mfg Part # WP3391914

High limit thermostat, L295-50F. If the dryer overheats, this high-limit thermostat will cut off the power to the heating element. If the high-limit thermostat has blown, the dryer will not heat.

Add to Cart