Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won't start or will run but not heat. The thermal fuse cannot be reset. Fuses often blow due to a clogged dryer vent.
Dryer drum drive belt. The belt is flat, 92-1/4 inches long, 1/4 inch wide and has 4 ribs and 3 grooves. It replaces many other belts, including some with 5 ribs and 4 grooves. If the drum does not turn, but you can hear the motor running then there is a good chance the belt has broken.
Dryer heating element. If your dryer does not heat first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases the heating element will have a break in the element if defective. *May need wire connector to install heating element.
Dryer drum support roller. If the dryer is making a rumbling or knocking noise the rollers may be worn out causing the drum not to turn smoothly.
Dryer heating element thermal cut-off (thermal fuse) 309 degrees and high limit thermostat 250 degrees, with wiring kit. If the dryer does not heat the thermal cut off may have blown and a new high limit thermostat is needed.
Dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective. To test, watch the burner and if the igniter glows for a while and then shuts off without the gas igniting, it usually means one of these coils is bad.
Dryer door switch assembly. If the dryer does not start then the door switch could be defective. This switch also replaces the two wire switch.
Repair kit for Whirlpool, Kenmore, Roper dryer; rollers, belt and idler pulley, for 29" wide Dryers built 1965 and later. This dryer maintenance kit contains all of the parts that are commonly defective when the dryer is noisy.
-Call with model# to verify if kit is compatible with your dryer.
Washer drive motor coupler. New style with metal sleeves for added strength. This version replaces all previous motor coupler styles and versions. For direct drive washing machines. Common symptom of failed coupler is washer will fill, not agitate or spin but will drain the water from the tub.
Dryer drum drive belt, 93 1/2 inches long, 4 ribs 3 grooves. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. If the drum will not turn when the dryer is turned on the belt is likely broken.
Dryer cycling thermostat with internal bias heater, L155-25. If the dryer won't heat, it is unlikely that this thermostat is causing the issue, as the thermal fuse or thermal cut-out normally fail first.
Dryer door catch kit. This kit includes three different door catches; you will need to select the door catch that fits your model.
Washing machine drain pump. The pump mounts directly to the motor with two clips. If the washer does not drain then the pump could be locked up or a small object may be clogging it. A small leak in front of the washer could be caused by a defective pump.
Washing machine agitator repair kit with a medium length cam (there are other kits available for different models). This kit should be used when the top part of the agitator is not moving properly but the bottom part is.
Quality Amana Washer/Dryer Combo Replacement Parts From Repair Clinic
Looking for Amana Washer/Dryer Combo Replacement Parts parts? RepairClinic.com has the appliance parts, lawn equipment parts and heating/cooling parts you need!
Common Amana Washer/Dryer Combo Problems
Start doing it yourself with the confidence that comes with 100+ years of experience. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right.
