Price Match Guarantee
Order by 2:00 a.m., and we'll ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment Repair>LG Top Load Washer Replace Rotor Position Sensor #6501KW2002A
LG Top Load Washer Replace Rotor Position Sensor #6501KW2002A
Skill Level
Total Parts Cost
$55.60Estimated Savings
$112.5003:26
- Description
This video provides step-by-step instructions for replacing the rotor position sensor on LG and Kenmore top-load washing machines. The most common reason for replacing the rotor position sensor is when it fails, causing the control panel to display an error code, which varies from model to model.
All of the information in this rotor position sensor replacement video is applicable to the following brands: LG, Kenmore
Tools used: adjustable wrench, hammer, 10mm socket, small flat-head screwdriver
All of the information in this rotor position sensor replacement video is applicable to the following brands: LG, Kenmore
Tools used: adjustable wrench, hammer, 10mm socket, small flat-head screwdriver
Step By Step Instructions
1
Before you replace the rotor sensor in your washer unplug the power cord
2
Shut off the water supply.
3
Next, remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
4
Carefully tip the washer back so it rests on the rear panel.
5
Now use an adjustable wrench and strike it with a hammer to help unthread the rotor mounting nut.
6
With the nut and washer removed, carefully pull off the rotor assembly.
7
Now use a 10mm socket to remove the mounting bolts securing the stator.
8
Carefully set the stator down and use a small flat-head screwdriver to help disconnect the wire connecters.
9
Detach the retaining clips to remove the old rotor sensor.
10
Install the new rotor sensor by aligning it on the stator and snapping it into place.
11
Connect the wire connecters.
12
Realign the stator on the clutch & bearing housing and replace the mounting bolts to secure.
13
Replace the rotor assembly by aligning it on the shaft.
14
Replace the washer and rethread the mounting nut.
15
Torque the nut to 88 foot pounds.
16
Return the washer to its upright position.
17
Reattach the hot and cold water supply lines to the inlet valve.
18
With the repair completed turn the water supply back on plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step instructions for replacing the rotor position sensor on LG and Kenmore top-load washing machines. The most common reason for replacing the rotor position sensor is when it fails, causing the control panel to display an error code, which varies from model to model.
All of the information in this rotor position sensor replacement video is applicable to the following brands: LG, Kenmore
Tools used: adjustable wrench, hammer, 10mm socket, small flat-head screwdriver
All of the information in this rotor position sensor replacement video is applicable to the following brands: LG, Kenmore
Tools used: adjustable wrench, hammer, 10mm socket, small flat-head screwdriver
Step-By-Step Instructions
1
Before you replace the rotor sensor in your washer unplug the power cord
2
Shut off the water supply.
3
Next, remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
4
Carefully tip the washer back so it rests on the rear panel.
5
Now use an adjustable wrench and strike it with a hammer to help unthread the rotor mounting nut.
6
With the nut and washer removed, carefully pull off the rotor assembly.
7
Now use a 10mm socket to remove the mounting bolts securing the stator.
8
Carefully set the stator down and use a small flat-head screwdriver to help disconnect the wire connecters.
9
Detach the retaining clips to remove the old rotor sensor.
10
Install the new rotor sensor by aligning it on the stator and snapping it into place.
11
Connect the wire connecters.
12
Realign the stator on the clutch & bearing housing and replace the mounting bolts to secure.
13
Replace the rotor assembly by aligning it on the shaft.
14
Replace the washer and rethread the mounting nut.
15
Torque the nut to 88 foot pounds.
16
Return the washer to its upright position.
17
Reattach the hot and cold water supply lines to the inlet valve.
18
With the repair completed turn the water supply back on plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Parts Needed
Rotor Position Sensor
$55.60
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com